By Alix Loane. Motor. Publised at Monday, January 29th 2018, 23:13:59 PM. Ideally, you will be connecting motors per an installation drawing. In that case, it’s a matter of correctly identifying the motor leads by number and connecting them per the drawing. Don’t try to “wing it” when replacing a motor, working with OEM equipment, or installing a motor when such drawings have been provided. But there’s a catch. We’ll get to that in a moment.
By Alix Loane. Circuit. Publised at Friday, February 09th 2018, 08:51:28 AM. Physical circuits are constructed of real, physical devices. They can be inspected, tested, and modified. They consume electric power when energized, and they can function properly and do some meaningful work, or they can malfunction and create serious hazards to health and property. Even small circuits that are quickly and easily constructed still take time and money to build, and they can take a very long time to perfect.
By Alix Loane. Motor. Publised at Friday, February 09th 2018, 07:11:13 AM. In the previous section it was shown that motor torque varies inversely with speed. This then is the motor’s natural speed-torque curve. Below a certain speed, called the corner speed, current would rise above the motor’s rated current, ultimately to destructive levels as the motor’s speed is reduced further.
By Charlotte Myriam. Motor. Published at Monday, December 18th 2017, 14:50:43 PM. In the previous section it was shown that motor torque varies inversely with speed. This then is the motor’s natural speed-torque curve. Below a certain speed, called the corner speed, current would rise above the motor’s rated current, ultimately to destructive levels as the motor’s speed is reduced further.
By Valentine Sybille. Power. Published at Monday, December 18th 2017, 14:14:34 PM. The control circuitry must monitor (sense) the output voltage, and adjust the current source (as required by the load) to hold the output voltage at the desired value. The design limit of the current source defines the maximum load current the regulator can source and still maintain regulation.
By Jessica Mireille. Circuit. Published at Monday, December 18th 2017, 14:08:09 PM. Voltage and current sources can be independent or dependent. Their respective circuit symbols. Independent sources are usually shown as a circle while dependent sources are usually shown as a diamond-shape. Independent sources can have a DC output or a functional output; some examples are a sine wave, square wave, impulse, and linear ramp. Dependent sources can be used to implement a voltage or current which is a function of some other voltage or current in the circuit. Dependent sources are often used to model active circuits that are used for signal amplification.
By Bertille Solange. Diagram. Published at Monday, December 18th 2017, 13:52:35 PM. A schematic shows connections in a circuit in a way that is clear and standardized. It is a way of communicating to other engineers exactly what components are involved in a circuit as well as how they are connected. A good schematic will show component names and values, and provide labels for sections or components to help communicate the intended purpose. Note how connections on wires (or "nets") are shown using dots and non-connections are shown without a dot.
By Charlotte Myriam. Circuit. Published at Monday, December 18th 2017, 13:45:45 PM. First let’s understand the difference between these two terms. While electrical is the basis of everything, electronic is a subset of electrical. An electrical circuit deals with just the flow of electrons and has components like resistors, inductors and capacitors and uses Alternating Current Source; while electronic circuit deals with the transformation of current and controlling the motion of the electrons and uses Direct Current Source. An electrical circuit is termed as Passive because it doesn’t have any such component that reacts to the current/voltage that passes through them and electronic circuit is called active because of the additional components like diode or a transformer that react to the current/voltage that passes through.
By Cyrielle Marjolaine. Diagram. Published at Monday, December 18th 2017, 13:32:30 PM. Sometimes, to make schematics more legible, we’ll give a net a name and label it, rather than routing a wire all over the schematic. Nets with the same name are assumed to be connected, even though there isn’t a visible wire connecting them. Names can either be written directly on top of the net, or they can be “tags”, hanging off the wire.
By Bertille Solange. Power. Published at Monday, December 18th 2017, 13:09:45 PM. The operation of the control loop in a typical linear regulator will be detailed using the simplified schematic diagram in Figure 2 (the function of the control loop is similar in all of the linear regulator types).
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.