By Cyrielle Marjolaine. Power. Publised at Monday, December 18th 2017, 10:47:11 AM. Load regulation refers to the ability of a voltage regulator to maintain a constant voltage as the load current varies and is expressed as a percentage. Ideally, the load regulation would be zero percent meaning that the output voltage is perfectly independent of the load current. The equation for load regulation is as follows.
By Sasha Sara. Motor. Published at Friday, January 05th 2018, 18:24:19 PM. At this point it is important to introduce the concept of overdrive ration. This is the ration between the power supply voltage and the motor’s rated voltage. An empirically derived maximum is 25:1, meaning the power supply voltage should never exceed 25 times the motor’s rated voltage or 32 times the square root of motor inductance. Below is a graph of measured iron losses for a 4A, 3V motor. Notice in Figure 16 how the iron losses range from insignificant to being the major cause of heating in the motor compared to a constant 12W copper loss (4A times 3V).
By Madeleine Catherine. Motor. Published at Friday, January 05th 2018, 16:16:10 PM. If more than one drive is being operated from the power supply this is not a problem since the other drive(s) will absorb this current for its needs, unless it is decelerating as well. For this case or for a single drive it may be necessary to place a voltage clamp across the power supply in the form of a Zener diode. The voltage of this diode must be greater than the maximum expected power supply voltage, yet low enough to protect the drive. A good choice would be either 82 volts or 91 volts as standard values.
By Bertille Solange. Circuit. Published at Friday, January 05th 2018, 13:36:25 PM. An electric current is defined as free flow of electrons and the motivating force behind that free flow of electrons is called Voltage. Voltage is the measurement of potential energy that would move the electrons between two points. Voltage is the push that the electrons require to move within a circuit. Voltage is measured by Volt and Current is measured by Ampere.
By Sasha Sara. Car Wiring. Published at Friday, January 05th 2018, 11:54:09 AM. The starter motor has its own heavy cable, direct from the battery. The ignition circuit furnishes the high-tension impulses to the sparkplugs; and the charging system includes the generator, which recharges the battery. All the other circuits are called ancillary (subsidiary) circuits.
By Bertille Solange. Motor. Published at Friday, January 05th 2018, 10:58:36 AM. If one changes the power supply voltage, then a new family of speed-torque curves result. As an example, if the power supply voltage is doubled then a new curve is generated; the curve now has twice the torque at any given speed in region 2. Since power equals torque times speed, the motor now generates twice as much power as well.
By Cyrielle Marjolaine. Diagram. Published at Friday, January 05th 2018, 09:04:28 AM. Be sure to use this to produce a schematic if you need to ask questions about your circuit. It will help others to quickly understand the circuit diagrams are pictures with symbols that have differed from country to country and have changed over time, but are now to a large extent internationally standardized. Simple components often had symbols intended to represent some feature of the physical construction of the device. For example, the symbol for a resistor shown here dates back to the days when that component was made from a long piece of wire wrapped in such a manner as to not produce inductance, which would have made it a coil. These wirewound resistors are now used only in high-power applications, smaller resistors being cast from carbon composition (a mixture of carbon and filler) or fabricated as an insulating tube or chip coated with a metal film. The internationally standardized symbol for a resistor is therefore now simplified to an oblong, sometimes with the value in ohms written inside, instead of the zig-zag symbol. A less common symbol is simply a series of peaks on one side of the line representing the conductor, rather than back-and-forth as shown here. Components and connections involved in your design.
By Jessica Mireille. Diagram. Published at Friday, January 05th 2018, 06:44:40 AM. In a digital circuit, power supply voltage levels are constrained to two distinct values – “logic high voltage” (called LHV or Vdd) and “logic low voltage” (called LLV or GND). The GND node in any circuit is the universal reference voltage against which all other voltages are measured (in modern digital circuits, GND is typically the lowest voltage in the circuit). In a schematic, it is often difficult to show lines connecting all GND nodes; rather, any nodes labeled GND are assumed to be connected into the same node. Often, a downward pointing triangle symbol, is attached to a GND node in addition to (or instead of) the GND label. The Vdd node in a digital circuit is typically the highest voltage, and all nodes labeled Vdd are tied together into the same node. Vdd may be thought of as the “source” of positive charges in a circuit, and GND may be thought of as the “source” of negative charges in a circuit. In modern digital systems, Vdd and GND are separated by anywhere from 1 to 5 volts. Older or inexpensive circuits typically use 5 volts, while newer circuits use 1-3 volts.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.