By Cyrielle Marjolaine. Power. Publised at Monday, December 18th 2017, 10:47:11 AM. The output resistance (also known as source resistance) of a voltage regulator is a close cousin of its load regulation. Figure 1 illustrates how the output voltage of a regulator typically changes as a function of load current. Initially, the slope is quite linear but once the load current becomes higher than the design then the voltage will often drop rapidly with an increase in current. We measure the output resistance only on the linear portion of the plot in the normal operating region. It is meaningless to use a point in the overload area as that will result in an artificially high output resistance.
By Bertille Solange. Circuit. Published at Tuesday, January 09th 2018, 21:42:21 PM. A basic understanding of electronic circuits is important even if the designer does not intend to become a proficient electrical engineer. In many real-life engineering projects, it is often necessary to communicate, and also negotiate, specifications between engineering teams having different areas of expertise. Therefore, a basic understanding of electronic circuits will allow the mechanical engineer to evaluate whether or not a given electrical specification is reasonable and feasible.
By Jessica Mireille. Car Wiring. Published at Tuesday, January 09th 2018, 21:35:41 PM. t is not a good idea to use push-on terminals. These can loosen and come off. If your gauge or other electrical components have those types of male terminals, you can drill a small hole in the blade and solder your wire to the terminal, then use shrink wrap to cover the connection. Remember to slide the shrink wrap over the wire before soldering.
By Charlotte Myriam. Car Wiring. Published at Tuesday, January 09th 2018, 20:33:26 PM. It just takes a little more time to duplicate your wiring into a spare wiring harness. Make two or three if you like, the parts are very inexpensive. Also keep spare switches on hand in your race trailer so that if one breaks or fails to function, you’ll be able to replace it quickly.
By Valentine Sybille. Circuit. Published at Tuesday, January 09th 2018, 17:51:25 PM. Many different types of components and devices can be found in modern circuits, including resistors, capacitors, and inductors, semiconductor devices like diodes, transistors, and integrated circuits, transducers like microphones, light sensors and motions sensors, actuators like motors and solenoids, and various other devices like heating and lighting elements. Devices in a circuit are connected to one another by means of electrical conductors, or wires. These wires can move electric currents between various points in a circuit. Once a wire connects two or more devices, the wire and all attached device connectors are said to form a single circuit node or net. Any electrical activity on a given net is communicated to all devices attached to the net. Certain nets provide electric power to devices, and other nets carry information between devices. Nets that carry information are called signals, and signals transport information encoded as voltage levels around a circuit. Signal nets typically use smaller conductors, and transport very small currents. Nets that carry power are called supply rails (or just supplies) and supply rails transport electric power around a circuit. Power nets typically use much larger conductors that signal nets, because they must transport larger currents.
By Jessica Mireille. Car Wiring. Published at Tuesday, January 09th 2018, 14:36:01 PM. When you begin the rewiring of your car, choose good material, as in new wire and quality terminals. Use a gauge of wire sufficient to carry the amperage load for the work it will be doing. Always use closed-end terminals, not the U type.
By Charlotte Myriam. Diagram. Published at Tuesday, January 09th 2018, 00:41:41 AM. Circuits often require output devices to communicate their state to an user. Examples of electronic output devices include computer monitors, LCD alphanumeric panels (as on a calculator), small lamps or light-emitting diodes (LED), etc. Digilent boards include different output devices, but all of them include some number of individual LED, and seven-segment LED displays that can display the digits 0-9 in each digit position (each segment in the seven-segment display contains a single LED). LED are two-terminal semiconductor devices that conduct current in only one direction (from the anode to the cathode). The small LED chips are secured inside a plastic housing, and they emit light at a givenfrequency (RED, YELLOW, etc.) when a small electric current (typically 10mA to 25mA) flows through them.
By Lydie Honorine. Diagram. Published at Monday, January 08th 2018, 17:19:46 PM. Circuits often require inputs that come directly from users (as opposed to inputs that come from other devices). User-input devices can take many forms, among them keyboards (as on a PC), buttons (as on a calculator or telephone), rotary dials, switches and levers, etc. Digilent boards include several input devices, typically including push buttons and slide-switches. Since digital circuits operate with two voltage levels (LHV or Vdd, and LLV or GND), input devices like buttons and switches should be able to produce both of these voltages based on some user action.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.