By Cyrielle Marjolaine. Motor. Publised at Thursday, June 08th 2017, 14:32:37 PM. Ideally, you will be connecting motors per an installation drawing. In that case, it’s a matter of correctly identifying the motor leads by number and connecting them per the drawing. Don’t try to “wing it” when replacing a motor, working with OEM equipment, or installing a motor when such drawings have been provided. But there’s a catch. We’ll get to that in a moment.
By Bertille Solange. Amplifier. Published at Monday, November 20th 2017, 03:11:46 AM. Unfortunately we are not quite done yet. I mentioned the concept of a ground loop earlier. This is a particularly insidious problem that can easily ruin a good project. In very general terms it is formed whenever there are multiple signal ground paths to the same termination. I can be internal or external to the piece of equipment. The most frequent result is a hum that either will not go away or happens only when something is connected to the piece of equipment. I need now to provide a few brief words about hum. If the hum is at the same frequency as the AC mains (either 50 or 60 Hz typically) then it is likely from interconnections external to the equipment or poor shielding internal to the equipment. If the hum is at twice the mains frequency then it nearly always because of inadequate power supply filtering. Ground loops are usually at the mains frequency. So if you encounter one, then you must search for the alternate ground paths that relate to the signal chain. If it external (occurs only when the equipment is attached to an external item), then check for things like phonograph grounding at the phonograph end. As an example I have seen is when one terminal of a cartridge connected to the ground in the tone arm (OK and fairly common) and a separate ground from the same tone arm (not OK) is provided for connection to the amplifier chassis ground (this is not to be confused to the situation when there is a separate ground wire from the phonograph chassis that has no connection to the ground in the cartridge). Since both the signal ground and tone arm ground are connected at the phonograph they will form a ground loop (between the shields and ground wire) when connected to the amplifier. The solution in such cases is to separate the grounds at the phonograph. An internal example was mentioned earlier when both ends of internal shielded cables are joined in two different places (at the input jacks and volume control). The irony of the situation and part of the insidious nature of ground loops is that they can on occasion be benign and not cause hum. They can later show up when a new piece of equipment is attached to the system. In all cases however, they have the same fundamental cause, alternate paths for the signal return.
By Charlotte Myriam. Diagram. Published at Monday, November 20th 2017, 02:05:43 AM. A block diagram shows a higher level (or organizational layout) of functional units in a circuit (or a device, machine, or collection of these). It is meant to show data flow or organization between separate units of function. A block diagram gives you an overview of the interconnected nature of circuit assemblies or components.
By Valentine Sybille. Diagram. Published at Monday, November 20th 2017, 01:56:04 AM. The unloaded PCB appears green because thin sheets of green plastic have been applied to both sides (otherwise the PCB would appear pale yellow). Called solder masks, these sheets cover all exposed metal other than the component pads and holes so that errant solder can not inadvertently short (or electrically connect) the printed wires. All metal surfaces other than the exposed pads and holes (i.e., the wires) are underneath the solder mask. Not infrequently, blue or even red solder masks are used.
By Bertille Solange. Diagram. Published at Monday, November 20th 2017, 01:12:22 AM. Learning about basic electronics and creating your own projects is a lot easier than you may think. In this tutorial, we’re going to give you a brief overview of common electronic components and explain what their functions are. You will then learn about schematic diagrams and how they are used to design and build circuits. And finally, you will put this information to use by creating your first basic circuit.
By Alix Loane. Circuit. Published at Monday, November 20th 2017, 00:59:13 AM. A simple low-pass filter circuit, which allows low frequency signals to pass through the circuit while attenuating high-frequency signals, can be made using a resistor and capacitor in series.The transfer function of this filter can be determined by analyzing the circuit as a voltage divider,
By Charlotte Myriam. Circuit. Published at Monday, November 20th 2017, 00:20:49 AM. Surface mount PCBs do not utilize wires as connectors. Instead, many small leads are soldered directly to the board, meaning that the board itself is used as a wiring surface for the different components. This allows circuits to be completed using less space, freeing up space to allow the board to complete more functions, usually at higher speeds and a lighter weight than a through-hole board would allow.
By Alix Loane. Circuit. Published at Monday, November 20th 2017, 00:18:44 AM. Impedance essentially can be viewed as frequency-dependent resistance. While resistance of a circuit is the instantaneous ratio between voltage and current, impedance of a circuit is the ratio between voltage and current for steady-state sinusoidal signals, which can vary with of frequency. As the later parts of this section will show, the voltage and current caused by applying a steady-state sinusoidal signal to any combination of resistors, capacitors, and inductors, are related by a constant factor and a phase shift. Therefore, impedance can be expressed by a complex constant using an extended version Ohm’s law.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.