By Cyrielle Marjolaine. Motor. Publised at Thursday, June 08th 2017, 14:32:37 PM. A real step motor has losses that modify the ideal speed-torque curve. The most important effect is the contribution of detent torque. Detent torque is usually specified in the motor datasheet. It is always a loss when the motor is turning and the power consumed to overcome it is proportional to speed. In other words, the faster the motor turns the greater the detent torque contributes power loss at the motor’s output shaft. This power loss is proportional to speed and must be subtracted from the ideal, flat output power curve past the corner speed. This now constitutes a practical speed-torque curve.
By Bertille Solange. Diagram. Published at Friday, December 22nd 2017, 11:10:29 AM. Knowing how to read circuits is a very useful skill that will help you out all the time. especially if you start messing around with building little electronics projects.
By Cyrielle Marjolaine. Diagram. Published at Friday, December 22nd 2017, 10:36:12 AM. Truly expansive schematics should be split into functional blocks. There might be a section for power input and voltage regulation, or a microcontroller section, or a section devoted to connectors. Try recognizing which sections are which, and following the flow of circuit from input to output. Really good schematic designers might even lay the circuit out like a book, inputs on the left side, outputs on the right.
By Bertille Solange. Diagram. Published at Friday, December 22nd 2017, 10:35:50 AM. Voltage nodes are single-terminal schematic components, which we can connect component terminals to in order to assign them to a specific voltage level. These are a special application of net names, meaning all terminals connected to a like-named voltage node are connected together.
By Lydie Honorine. Circuit. Published at Friday, December 22nd 2017, 09:24:31 AM. Electronic signals are represented either by voltage or current. The timedependent characteristics of voltage or current signals can take a number of forms including DC, sinusoidal (also known as AC), square wave, linear ramps, and pulsewidth modulated signals. Sinusoidal signals are perhaps the most important signal forms since once the circuit response to sinusoidal signals are known, the result can be generalized to predict how the circuit will respond to a much greater variety of signals using the mathematical tools of Fourier and Laplace transforms.
By Bertille Solange. Diagram. Published at Friday, December 22nd 2017, 08:20:00 AM. Knowing how to read circuits is a very useful skill that will help you out all the time. especially if you start messing around with building little electronics projects.
By Charlotte Myriam. Circuit. Published at Friday, December 22nd 2017, 07:40:14 AM. Electric circuits use electric power to perform some function, like energize a heating or lighting element, turn a motor, or create an electromagnetic filed. Electronic circuits differ from electric circuits in that they use devices that can themselves be controlled by other electric signals. Restated, electronic circuits are built from devices that use electricity to control electricity. Most electronic circuits use signals that are within 5 to 10 volts of ground; most circuits built within the past several years use signals that are within 3 to 5 volts from ground. Some electronic circuits represent information encoded as continuous voltage levels that can wander between the high and low voltage supply rails – these are called analog circuits. As an example, a sound pressure level transducer (i.e. a microphone) might drive a signal between 0V and 3.3V in direct proportion to the detected sound pressure level. In this case, the voltage signal output from the microphone is said to be an analog ifthe sound pressure wave itself. Other circuits use only two distinct voltage levels to represent information. Most often, these two voltage levels use the same voltages supplied by the power rails. In these circuits, called digital circuits, all information must be represented as binary numbers, with a signal at 0V (or ground) representing one kind of information, and a signal at 3.3V (or whatever the upper voltage supply rail provides) representing the other kind of information. In this series of modules, we will confine our discussions to digital circuits.
By Charlotte Myriam. Circuit. Published at Thursday, December 21st 2017, 23:38:50 PM. An often used and sometimes confusing term in electronic circuits is the word ground. The ground is a circuit node to which all voltages in a circuit are referenced. In a constant voltage supply circuit, one terminal from each voltage supply is typically connected to ground, or is grounded. For example, the negative terminal of a positive power supply is usually connected to ground so that any current drawn out of the positive terminal can be put back into the negative terminal via ground.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.