By Cyrielle Marjolaine. Motor. Publised at Thursday, June 08th 2017, 14:32:37 PM. The easiest factor in choosing a power supply is its current rating, which is based on your motor ratings. A motor control will always draw less than 2/3 of the motor’s rated current when it is parallel (or half-winding) connected and 1/3 of the motor’s rated current when it is series (or full-winding) connected. That is to say, a 6 amp per phase motor will require a 4 amp power supply when wired in parallel and a 2 amp power supply when wired in series. If multiple motors and drives are used, add the current requirements of each to arrive at the total power supply current rating.
By Cyrielle Marjolaine. Circuit. Published at Saturday, December 23rd 2017, 00:11:04 AM. Ohm’s law states that the current through a conductor between two points is directly proportional to the potential difference across those two points. It means that more the resistance lesser current would flow. I=V/R This would apply to any component of a circuit. For example conductors would increase the current flow and the inductors would decrease it.
By Lydie Honorine. Circuit. Published at Friday, December 22nd 2017, 23:34:06 PM. Electric circuits use electric power to perform some function, like energize a heating or lighting element, turn a motor, or create an electromagnetic filed. Electronic circuits differ from electric circuits in that they use devices that can themselves be controlled by other electric signals. Restated, electronic circuits are built from devices that use electricity to control electricity. Most electronic circuits use signals that are within 5 to 10 volts of ground; most circuits built within the past several years use signals that are within 3 to 5 volts from ground. Some electronic circuits represent information encoded as continuous voltage levels that can wander between the high and low voltage supply rails – these are called analog circuits. As an example, a sound pressure level transducer (i.e. a microphone) might drive a signal between 0V and 3.3V in direct proportion to the detected sound pressure level. In this case, the voltage signal output from the microphone is said to be an analog ifthe sound pressure wave itself. Other circuits use only two distinct voltage levels to represent information. Most often, these two voltage levels use the same voltages supplied by the power rails. In these circuits, called digital circuits, all information must be represented as binary numbers, with a signal at 0V (or ground) representing one kind of information, and a signal at 3.3V (or whatever the upper voltage supply rail provides) representing the other kind of information. In this series of modules, we will confine our discussions to digital circuits.
By Cyrielle Marjolaine. Motor. Published at Friday, December 22nd 2017, 23:06:28 PM. An unregulated power supply will be sufficient and is recommended for most applications because of its simplicity. If a motor with a large inertial load decelerates quickly it will act as an alternator and send voltage back to the drive which then sends it back to the power supply. Because many regulated power supplies feature protection circuitry this may cause the power supply to fault or reset; however, if the supply is unregulated it will simply get absorbed by the filter capacitor.
By Cyrielle Marjolaine. Diagram. Published at Friday, December 22nd 2017, 21:40:25 PM. A PCB Layout is the resulting design from taking a schematic with specific components and determining how they will physically be laid out on a printed circuit board. To produce a PCB Layout, you must know the connections of components, component sizes (footprints), and a myriad of other properties (such as current, frequencies, emissions, reflections, high voltage gaps, safety considerations, manufacturing tolerances, etc.).
By Alix Loane. Circuit. Published at Friday, December 22nd 2017, 21:26:48 PM. A basic understanding of electronic circuits is important even if the designer does not intend to become a proficient electrical engineer. In many real-life engineering projects, it is often necessary to communicate, and also negotiate, specifications between engineering teams having different areas of expertise. Therefore, a basic understanding of electronic circuits will allow the mechanical engineer to evaluate whether or not a given electrical specification is reasonable and feasible.
By Madeleine Catherine. Motor. Published at Friday, December 22nd 2017, 21:10:31 PM. At this point it is important to introduce the concept of overdrive ration. This is the ration between the power supply voltage and the motor’s rated voltage. An empirically derived maximum is 25:1, meaning the power supply voltage should never exceed 25 times the motor’s rated voltage or 32 times the square root of motor inductance. Below is a graph of measured iron losses for a 4A, 3V motor. Notice in Figure 16 how the iron losses range from insignificant to being the major cause of heating in the motor compared to a constant 12W copper loss (4A times 3V).
By Valentine Sybille. Circuit. Published at Friday, December 22nd 2017, 20:36:12 PM. There are two kinds of energy sources in electronic circuits: voltage sources and current sources. When connected to an electronic circuit, an ideal voltage source maintains a given voltage between its two terminals by providing any amount of current necessary to do so. Similarly, an ideal current source maintains a given current to a circuit by providing any amount of voltage across its terminals necessary to do so.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.