By Cyrielle Marjolaine. Motor. Publised at Thursday, June 08th 2017, 14:32:37 PM. As shown earlier, motor output power is proportional to power supply voltage, doubling the voltage doubles the output power. However, iron losses outpace motor power by increasing non-linearly with increasing power supply voltage. Eventually the point is reached where the iron losses are so great that the motor cannot dissipate the heat generated. In a way this is nature’s way of keeping someone from getting 500HP from a NEMA 23 motor by using a 10kV power supply.
By Madeleine Catherine. Circuit. Published at Saturday, July 01st 2017, 02:55:55 AM. A collection of electronic components that have been assembled and interconnected to perform a given function is commonly referred to as a circuit. The word circuit derives from the fact that electric power must flow from the positive terminal of a power source through one or more electronic devices and back to the negative terminal of a power source, thereby forming a circuit. If the connections between an electronic device and either the positive or negative terminals of a power supply are interrupted, the circuit will be broken and the device will not function.
By Bertille Solange. Circuit. Published at Friday, June 30th 2017, 01:44:35 AM. Voltage and current sources can be independent or dependent. Their respective circuit symbols. Independent sources are usually shown as a circle while dependent sources are usually shown as a diamond-shape. Independent sources can have a DC output or a functional output; some examples are a sine wave, square wave, impulse, and linear ramp. Dependent sources can be used to implement a voltage or current which is a function of some other voltage or current in the circuit. Dependent sources are often used to model active circuits that are used for signal amplification.
By Cyrielle Marjolaine. Motor. Published at Thursday, June 29th 2017, 01:05:11 AM. An unregulated power supply will be sufficient and is recommended for most applications because of its simplicity. If a motor with a large inertial load decelerates quickly it will act as an alternator and send voltage back to the drive which then sends it back to the power supply. Because many regulated power supplies feature protection circuitry this may cause the power supply to fault or reset; however, if the supply is unregulated it will simply get absorbed by the filter capacitor.
By Alix Loane. Diagram. Published at Sunday, June 25th 2017, 01:04:57 AM. A schematic shows connections in a circuit in a way that is clear and standardized. It is a way of communicating to other engineers exactly what components are involved in a circuit as well as how they are connected. A good schematic will show component names and values, and provide labels for sections or components to help communicate the intended purpose. Note how connections on wires (or "nets") are shown using dots and non-connections are shown without a dot.
By Bertille Solange. Circuit. Published at Friday, June 23rd 2017, 23:36:14 PM. Electric current is the rate at which electric charge flows through a given area. Current is measured in the unit of Coulombs per second, which is known as an ampere (A). In an electronic circuit, the electromagnetic problem of currents is typically simplified as a current flowing through particular circuit components.
By Jessica Mireille. Power. Published at Tuesday, June 20th 2017, 23:07:42 PM. In shunt regulation a resistor is typically placed in series with the load and the unregulated voltage. The resistor is small enough so that the load could always receive somewhat more than the maximum current it would ever need. The shunt regulator is placed across the load and conducts excess current around the load such that the voltage across the load remains a constant as the load draws the actual current at any given time. A common shunt regulator is a Zener diode which is an example of an open loop system. Feedback control can also be used to drive the current through the control element (a transistor) across the load. Shunt regulators are generally only used for low power applications because they can be very inefficient. However, shunt regulators have an inherent fault current limiting feature and also can regulate even if the load is forcing current into the regulator rather than drawing current from it. Shunt regulators also have an interesting feature that the input current is constant – independent of load current (except if a load fault occurs – but that is a special case not in normal operation). Thus shunt regulators are very good at isolating a load with rapid and large current fluctuations.
By Bertille Solange. Circuit. Published at Monday, June 19th 2017, 22:23:18 PM. A simple low-pass filter circuit, which allows low frequency signals to pass through the circuit while attenuating high-frequency signals, can be made using a resistor and capacitor in series.The transfer function of this filter can be determined by analyzing the circuit as a voltage divider,
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.