By Charlotte Myriam. Circuit. Publised at Friday, December 01st 2017, 09:55:05 AM. Electric current is the rate at which electric charge flows through a given area. Current is measured in the unit of Coulombs per second, which is known as an ampere (A). In an electronic circuit, the electromagnetic problem of currents is typically simplified as a current flowing through particular circuit components.
By Charlotte Myriam. Power. Published at Monday, November 20th 2017, 04:27:15 AM. Load regulation refers to the ability of a voltage regulator to maintain a constant voltage as the load current varies and is expressed as a percentage. Ideally, the load regulation would be zero percent meaning that the output voltage is perfectly independent of the load current. The equation for load regulation is as follows.
By Bertille Solange. Diagram. Published at Monday, November 20th 2017, 04:20:57 AM. A digital circuit is constructed of a power supply, devices, and conduction nets. Some nets provide circuit inputs from the “outside world”; in a schematic, these input nets are generally shown entering the left side of component and/or the overall circuit. Other nets present circuit outputs to the outside world; these nets are generally shown exiting the schematic on the right. In the sample schematic below, circuit components are shown as arbitrary shapes, nets are shown as lines, and inputs and outputs are denoted by connector symbols.
By Jessica Mireille. Diagram. Published at Monday, November 20th 2017, 03:57:49 AM. Variable resistors and potentiometers each augment the standard resistor symbol with an arrow. The variable resistor remains a two-terminal device, so the arrow is just laid diagonally across the middle. A potentiometer is a three-terminal device, so the arrow becomes the third terminal (the wiper).
By Charlotte Myriam. Diagram. Published at Monday, November 20th 2017, 03:19:30 AM. A schematic shows connections in a circuit in a way that is clear and standardized. It is a way of communicating to other engineers exactly what components are involved in a circuit as well as how they are connected. A good schematic will show component names and values, and provide labels for sections or components to help communicate the intended purpose. Note how connections on wires (or "nets") are shown using dots and non-connections are shown without a dot.
By Bertille Solange. Amplifier. Published at Monday, November 20th 2017, 03:11:46 AM. In a class B amplifier, no DC voltage is used to bias the transistors, so for the output transistors to start to conduct each half of the waveform, both positive and negative, they need the base-emitter voltage Vbe to be greater than the 0.7v required for a bipolar transistor to start conducting.
By Charlotte Myriam. Diagram. Published at Monday, November 20th 2017, 02:05:43 AM. Circuits often require output devices to communicate their state to an user. Examples of electronic output devices include computer monitors, LCD alphanumeric panels (as on a calculator), small lamps or light-emitting diodes (LED), etc. Digilent boards include different output devices, but all of them include some number of individual LED, and seven-segment LED displays that can display the digits 0-9 in each digit position (each segment in the seven-segment display contains a single LED). LED are two-terminal semiconductor devices that conduct current in only one direction (from the anode to the cathode). The small LED chips are secured inside a plastic housing, and they emit light at a givenfrequency (RED, YELLOW, etc.) when a small electric current (typically 10mA to 25mA) flows through them.
By Valentine Sybille. Diagram. Published at Monday, November 20th 2017, 01:56:04 AM. Starting to make sense? These are the basics and may even seem obvious or intuitive to you, such as the wires and if they are connected. Whenever you determine your specific field of electrical engineering, you may see more complex diagrams and symbols. You’ll learn also that different countries use different symbols. For example, of the two symbols for resistors above, the first one is used in the U.S., while the second is used in Europe. You will also learn about the various symbols used for switches, other power supplies, inductors, meters, lamps, LEDs, transistors, antennas, and much more.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.