By Charlotte Myriam.

Diagram. Publised at Monday, November 20th 2017, 05:12:37 AM. As discussed earlier, a digital circuit represents and manipulates information encoded as electric signals that can assume one of two voltages – logic-high voltage (or Vdd) and logic-low voltage (or GND). A digital circuit requires a power supply that can produce these two voltages, and these same supply voltages are also used to encode information in the form of two-state, or binary signals. Thus,if a given circuit node is at Vdd, then that signal is said to carry a logic ‘1’; if the node is at GND, then the node carries a logic ‘0’. The components in digital circuits are simple on/off switches that can pass logic ‘1’ and logic ‘0’ signals from one circuit node to another. Most typically, these switches are arranged to combine input signals to produce an output signal according to basic logic relationships. For example, one well-known logic circuit is an AND gate that combines two input signals to produce an output that is the logic AND of the inputs (i.e., if both input1 and input2 are a ‘1’, then the output is a ‘1’).

By Cyrielle Marjolaine.

Circuit. Published at Saturday, December 16th 2017, 16:15:18 PM. The circuits and components of a double-layer PCB board are usually connected in one of two ways: either utilizing a through-hole or with the use of a surface-mount. A through-hole connection means that small wires, known as leads, are fed through the holes, with each end of the leads then soldered to the right component.

By Lydie Honorine.

Power. Published at Saturday, December 16th 2017, 16:09:24 PM. Voltage regulation is the process of holding a voltage steady under conditions of changing applied voltage and changing load current. Many electronic systems require a stable power supply voltage and use voltage regulators to accomplish that.

By Madeleine Catherine.

Circuit. Published at Saturday, December 16th 2017, 14:21:35 PM. For DC signals, the linearity of the system implies that H is independent of Vin. For dynamic signals, the transfer function cannot in general be described simply. However, if the input is a sinusoidal signal then the output must also be a sinusoidal signal with the same frequency but possibly a different amplitude and phase. In other words, a linear system can only modify the amplitude and phase of a sinusoidal input.

By Madeleine Catherine.

Circuit. Published at Saturday, December 16th 2017, 11:35:09 AM. In the hydrodynamic analogy of electronic circuits, resistors are equivalent to a pipe. As fluid flows through a pipe, frictional drag forces at the walls dissipate energy from the flow and thus reducing the pressure, or equivalently, the potential energy of the fluid in the pipe. A small resistor is equivalent to a large diameter pipe that will allow for a high flow rate, whereas a large resistor is equivalent to a small diameter pipe that greatly constricts the flow rate.

By Sasha Sara.

Circuit. Published at Saturday, December 16th 2017, 07:52:40 AM. We all know about electricity. It is the flow electrons. Hence the word electricity is derived from the word electrons. A battery itself doesn’t work, if you hold it up in air, there would be no passage of electric current. Hence you need a circuit. In Simple terms an electronic circuit is a closed pathway for electrons to flow.

By Cyrielle Marjolaine.

Circuit. Published at Saturday, December 16th 2017, 06:37:27 AM. Many different types of components and devices can be found in modern circuits, including resistors, capacitors, and inductors, semiconductor devices like diodes, transistors, and integrated circuits, transducers like microphones, light sensors and motions sensors, actuators like motors and solenoids, and various other devices like heating and lighting elements. Devices in a circuit are connected to one another by means of electrical conductors, or wires. These wires can move electric currents between various points in a circuit. Once a wire connects two or more devices, the wire and all attached device connectors are said to form a single circuit node or net. Any electrical activity on a given net is communicated to all devices attached to the net. Certain nets provide electric power to devices, and other nets carry information between devices. Nets that carry information are called signals, and signals transport information encoded as voltage levels around a circuit. Signal nets typically use smaller conductors, and transport very small currents. Nets that carry power are called supply rails (or just supplies) and supply rails transport electric power around a circuit. Power nets typically use much larger conductors that signal nets, because they must transport larger currents.

By Lydie Honorine.

Circuit. Published at Saturday, December 16th 2017, 06:16:53 AM. A basic understanding of electronic circuits is important even if the designer does not intend to become a proficient electrical engineer. In many real-life engineering projects, it is often necessary to communicate, and also negotiate, specifications between engineering teams having different areas of expertise. Therefore, a basic understanding of electronic circuits will allow the mechanical engineer to evaluate whether or not a given electrical specification is reasonable and feasible.

Recent post

- Ih 284 Tractor Wiring Diagram
- John Deere Model 50 Engine Diagram
- Dodge Dart Steering Column Wiring
- Honda Odyssey Transmission Wiring Diagrams
- Jeep Cj Wiring Diagram For Starter
- John Deere 2120 Wiring Diagram
- John Deere L118 Wiring Schematics
- Diagram Rover Engine Discovery 2013
- Light Fixture Dimmer Wire Diagram
- John Deere Model A Engine Diagram

Category

Monthly Archives

Static Page

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z - 0 1 2 3 4 5 6 7 8 9

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z - 0 1 2 3 4 5 6 7 8 9

Altrushare - Wiring Diagram Gallery

Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.