By Jessica Mireille.

Motor. Publised at Thursday, December 21st 2017, 11:37:52 AM. The voltage of your power supply is entirely dependent on the inductance rating of your motor, which we learned is translatable to the number of turns of wire in the stator. Every motor model will have a different inductance rating and will therefore have a different maximum voltage. To figure out what the maximum power supply voltage should be, use the following formula with the motor’s inductance in millihenries (mH) used for the L value.

By Charlotte Myriam.

Motor. Publised at Monday, December 18th 2017, 14:50:43 PM. The easiest factor in choosing a power supply is its current rating, which is based on your motor ratings. A motor control will always draw less than 2/3 of the motor’s rated current when it is parallel (or half-winding) connected and 1/3 of the motor’s rated current when it is series (or full-winding) connected. That is to say, a 6 amp per phase motor will require a 4 amp power supply when wired in parallel and a 2 amp power supply when wired in series. If multiple motors and drives are used, add the current requirements of each to arrive at the total power supply current rating.

By Cyrielle Marjolaine.

Circuit. Published at Sunday, December 17th 2017, 15:08:00 PM. There are two kinds of energy sources in electronic circuits: voltage sources and current sources. When connected to an electronic circuit, an ideal voltage source maintains a given voltage between its two terminals by providing any amount of current necessary to do so. Similarly, an ideal current source maintains a given current to a circuit by providing any amount of voltage across its terminals necessary to do so.

By Bertille Solange.

Power. Published at Sunday, December 17th 2017, 14:30:46 PM. It is possible for RO to be negative – an undesirable characteristic often caused by poor layout design in the regulator wiring resulting in inadvertent positive feedback. With negative output resistance the output voltage increases with the load current.

By Jessica Mireille.

Circuit. Published at Sunday, December 17th 2017, 11:52:33 AM. The real part and imaginary part of impedance are interpreted as a resistive part that dissipates energy and a reactive part that stores energy. Resistors can only dissipate energy and therefore their impedances have only a real part. Capacitors and inductors can only store energy and therefore their impedances have only an imaginary part. When resistors, capacitors, and inductors are combined, the overall impedance may have both real and imaginary parts. It is important to note that the definition of impedance preserves the definition of resistance.

By Madeleine Catherine.

Circuit. Published at Sunday, December 17th 2017, 05:58:47 AM. Voltage and current sources can be independent or dependent. Their respective circuit symbols. Independent sources are usually shown as a circle while dependent sources are usually shown as a diamond-shape. Independent sources can have a DC output or a functional output; some examples are a sine wave, square wave, impulse, and linear ramp. Dependent sources can be used to implement a voltage or current which is a function of some other voltage or current in the circuit. Dependent sources are often used to model active circuits that are used for signal amplification.

By Madeleine Catherine.

Power. Published at Sunday, December 17th 2017, 00:51:45 AM. The Standard regulator is usually best for AC-powered applications, where the low cost and high load current make it the ideal choice. In AC-powered applications, the voltage across the regulator is usually at least 3V or more, so dropout voltage is not critical.

By Madeleine Catherine.

Circuit. Published at Sunday, December 17th 2017, 00:43:41 AM. Impedance is one of the most important concepts in electronic circuits. The purpose of impedance is to generalize the idea of resistance to create a component. To capture the behavior of resistors, capacitors, and inductors, for steadystate sinusoidal signals. This generalization is motivated by the fact that as long as the circuit is linear, its behavior can be analyzed using KVL and KCL.

By Valentine Sybille.

Diagram. Published at Sunday, December 17th 2017, 00:08:54 AM. Variable resistors and potentiometers each augment the standard resistor symbol with an arrow. The variable resistor remains a two-terminal device, so the arrow is just laid diagonally across the middle. A potentiometer is a three-terminal device, so the arrow becomes the third terminal (the wiper).

Recent post

- Lincoln Engine Diagrams
- Ls3 Wiring Diagram
- Disposal Dishwasher Wiring Diagram
- Industrial Door Opener Wiring-diagram
- Diagram Of Rotary Engine
- Jacobs Brake Wiring Diagram
- Internal Thermostat Wiring Diagram
- Jacobn 628d Blade Switch Wiring Diagram For Power
- Impala Power Seats Wiring-diagram
- John Deere 2020 L Wiring Diagram

Category

Monthly Archives

Static Page

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z - 0 1 2 3 4 5 6 7 8 9

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z - 0 1 2 3 4 5 6 7 8 9

Altrushare - Wiring Diagram Gallery

Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.