By Charlotte Myriam. Diagram. Publised at Monday, November 20th 2017, 05:12:37 AM. Production circuit boards typically start out as thin sheets of fiberglass (about 1mm thick) that are completely covered on both sides with very thin sheets of metal (typically copper). A "standard" circuit board might use a 1 ounce copper process, which means that one ounce of copper is evenly spread across 1 square foot of circuit board. During the manufacturing process, wire patterns are "printed" onto the copper surfaces using a compound that resists etching (hence the name Printed Circuit Board or PCB). The boards are subjected to a chemical etching process that removes all exposed copper. The remaining, un-etched copperforms wires that will interconnect the circuit board components, and small pads that define the regions where component leads will be attached.
By Madeleine Catherine. Diagram. Published at Monday, December 18th 2017, 04:49:04 AM. Learning about basic electronics and creating your own projects is a lot easier than you may think. In this tutorial, we’re going to give you a brief overview of common electronic components and explain what their functions are. You will then learn about schematic diagrams and how they are used to design and build circuits. And finally, you will put this information to use by creating your first basic circuit.
By Valentine Sybille. Circuit. Published at Monday, December 18th 2017, 04:45:11 AM. Electronic signals are represented either by voltage or current. The timedependent characteristics of voltage or current signals can take a number of forms including DC, sinusoidal (also known as AC), square wave, linear ramps, and pulsewidth modulated signals. Sinusoidal signals are perhaps the most important signal forms since once the circuit response to sinusoidal signals are known, the result can be generalized to predict how the circuit will respond to a much greater variety of signals using the mathematical tools of Fourier and Laplace transforms.
By Cyrielle Marjolaine. Circuit. Published at Sunday, December 17th 2017, 15:08:00 PM. Electric circuits use electric power to perform some function, like energize a heating or lighting element, turn a motor, or create an electromagnetic filed. Electronic circuits differ from electric circuits in that they use devices that can themselves be controlled by other electric signals. Restated, electronic circuits are built from devices that use electricity to control electricity. Most electronic circuits use signals that are within 5 to 10 volts of ground; most circuits built within the past several years use signals that are within 3 to 5 volts from ground. Some electronic circuits represent information encoded as continuous voltage levels that can wander between the high and low voltage supply rails – these are called analog circuits. As an example, a sound pressure level transducer (i.e. a microphone) might drive a signal between 0V and 3.3V in direct proportion to the detected sound pressure level. In this case, the voltage signal output from the microphone is said to be an analog ifthe sound pressure wave itself. Other circuits use only two distinct voltage levels to represent information. Most often, these two voltage levels use the same voltages supplied by the power rails. In these circuits, called digital circuits, all information must be represented as binary numbers, with a signal at 0V (or ground) representing one kind of information, and a signal at 3.3V (or whatever the upper voltage supply rail provides) representing the other kind of information. In this series of modules, we will confine our discussions to digital circuits.
By Bertille Solange. Power. Published at Sunday, December 17th 2017, 14:30:46 PM. In series regulation the control element is placed between the unregulated voltage source and the load and the current through the element is controlled so that the voltage across the load is held constant. A feedback control system is used where the difference between the output voltage and a reference voltage is applied to a high gain amplifier that drives the current control element such as to maintain the setpoint output voltage. The majority of voltage regulators are of the series type.
By Jessica Mireille. Circuit. Published at Sunday, December 17th 2017, 11:52:33 AM. Physical circuits are constructed of real, physical devices. They can be inspected, tested, and modified. They consume electric power when energized, and they can function properly and do some meaningful work, or they can malfunction and create serious hazards to health and property. Even small circuits that are quickly and easily constructed still take time and money to build, and they can take a very long time to perfect.
By Madeleine Catherine. Circuit. Published at Sunday, December 17th 2017, 05:58:47 AM. When multiple components are connected in series, each component must carry the same current. When multiple components are connected in parallel, the total current is the sum of the currents flowing through each individual component. These statements are generalized as Kirchoff’s Current Law (KCL), which states that the sum of currents entering and exiting a node must be zero.
By Madeleine Catherine. Power. Published at Sunday, December 17th 2017, 00:51:45 AM. The maximum current required in an application should be carefully considered when selecting an IC regulator. The load current specification for an IC regulator will be defined as either a single value or a value that is dependent on input-output voltage differential (this is detailed in the following section on protection circuits).
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.