By Bertille Solange. Circuit. Publised at Friday, June 30th 2017, 01:44:35 AM. In the hydrodynamic analogy of electronic circuits, resistors are equivalent to a pipe. As fluid flows through a pipe, frictional drag forces at the walls dissipate energy from the flow and thus reducing the pressure, or equivalently, the potential energy of the fluid in the pipe. A small resistor is equivalent to a large diameter pipe that will allow for a high flow rate, whereas a large resistor is equivalent to a small diameter pipe that greatly constricts the flow rate.
By Charlotte Myriam. Car Wiring. Published at Tuesday, January 09th 2018, 20:33:26 PM. All of the ground wires in the cockpit can be run to the forward frame grounding post and the battery ground can be run to the frame at the rear or wherever you mount the battery. The exception in his case is the ignition ground, which he runs separate from the other ground wires directly to the battery ground.
By Valentine Sybille. Circuit. Published at Tuesday, January 09th 2018, 17:51:25 PM. If the components of the circuit are connected in one single path is it termed as series. The same current would flow through all the components while the voltage would differ from one component to another. For example you have lit three lamps in series to the same power source, the first one would receive more voltage than the last.
By Jessica Mireille. Car Wiring. Published at Tuesday, January 09th 2018, 14:36:01 PM. I cannot tell you how many teams have connected these wires thinking purple must go with purple. It does not. Note the location of each wire on both sides of the original connectors and identify them with markings before you cut off the old connector.
By Charlotte Myriam. Diagram. Published at Tuesday, January 09th 2018, 00:41:41 AM. Several different resistors are used on Digilent boards. Some are used to limit LED current, and some are used on inputs (like the button and switch circuits) to both limit the currents flowing to the main chip, and to help protect against electrostatic discharge (or ESD – more on this topic later). The resistors on the Digilent boards, like most resistors used in digital systems, are physically small because they will not encounter large voltages or currents. For these smaller resistors, the resistor value in Ohms is printed in microscopic numbers on the resistor body, not visible to the naked eye.
By Lydie Honorine. Diagram. Published at Monday, January 08th 2018, 17:19:46 PM. There are two commonly used capacitor symbols. One symbol represents a polarized (usually electrolytic or tantalum) capacitor, and the other is for non-polarized caps. In each case there are two terminals, running perpendicularly into plates. The symbol with one curved plate indicates that the capacitor is polarized. The curved plate represents the cathode of the capacitor, which should be at a lower voltage than the positive, anode pin. A plus sign might also be added to the positive pin of the polarized capacitor symbol.
By Valentine Sybille. Diagram. Published at Monday, January 08th 2018, 15:30:16 PM. Production circuit boards typically start out as thin sheets of fiberglass (about 1mm thick) that are completely covered on both sides with very thin sheets of metal (typically copper). A "standard" circuit board might use a 1 ounce copper process, which means that one ounce of copper is evenly spread across 1 square foot of circuit board. During the manufacturing process, wire patterns are "printed" onto the copper surfaces using a compound that resists etching (hence the name Printed Circuit Board or PCB). The boards are subjected to a chemical etching process that removes all exposed copper. The remaining, un-etched copperforms wires that will interconnect the circuit board components, and small pads that define the regions where component leads will be attached.
By Cyrielle Marjolaine. Diagram. Published at Monday, January 08th 2018, 11:14:03 AM. A digital circuit requires a power supply to provide a constant and stable source of electric power to all devices. As discussed above, electric power is derived from the basic electrical forces that charged particles (e.g., protons and electrons) exert on one another – namely, electrons are repelled by other electrons, and attracted to more electrically positive areas where there are relatively fewer electrons. The vast majority of charged particles are found in ordinary matter bound in electrically neutral atomic structures (that is, most particles are found in structures that have an equal number of positive and negative particles). Some electrically neutral conducting materials (like metals) contain electrons that are not so tightly bound to their host atoms. If a voltage source is applied to these materials, the lightly bound electrons will move away from the concentrated source of electrons on the negative side of the supply towards the electrically positive side of the supply. A “power supply” in a digital circuit provides a local, contained imbalance of electrons that provides a voltage source that can do useful work, such as transmitting information through a conductor from one device to another. A digital circuit allows a controlled flow of electrons from of the negative to positive side of the power supply, but only via the paths designed into the circuit. As electrons flow to and from the devices in a given circuit, they can change device properties in useful ways.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.