By Lydie Honorine. Car Wiring. Publised at Saturday, December 30th 2017, 07:30:01 AM. The most common type of fuse is a short length of thin wire enclosed in a heatproof casing often glass. The size of the fuse wire is the thinnest that can carry the normal current of the circuit without overheating, and it is rated in amps.
By Valentine Sybille. Car Wiring. Publised at Saturday, December 30th 2017, 12:56:44 PM. As we stated, always use closed terminals. If your terminals have the plastic cover, remove that. Always solder the terminal where the wire end is installed. Never crimp the terminal and expect the wire to stay there forever. It won’t.
By Valentine Sybille. Circuit. Published at Friday, December 22nd 2017, 19:21:35 PM. First let’s understand the difference between these two terms. While electrical is the basis of everything, electronic is a subset of electrical. An electrical circuit deals with just the flow of electrons and has components like resistors, inductors and capacitors and uses Alternating Current Source; while electronic circuit deals with the transformation of current and controlling the motion of the electrons and uses Direct Current Source. An electrical circuit is termed as Passive because it doesn’t have any such component that reacts to the current/voltage that passes through them and electronic circuit is called active because of the additional components like diode or a transformer that react to the current/voltage that passes through.
By Charlotte Myriam. Diagram. Published at Friday, December 22nd 2017, 18:19:02 PM. The slide switches are also known as “single throw-double pole” (STDP) switches, because only one switch (or throw) exists, but two positions (or poles) are available (a pole is an electrical contact to which the switch can make contact). These switches can be set to output either Vdd (when the actuator is closest to the board’s edge) or GND. The push button switches are also known as “momentary” contact buttons, because they only make contact while they are actively being pressed – they output a GND at rest, and a Vdd only when they are being pressed. The figure below shows typically pushbutton and slide switch circuits used on Digilent boards.
By Lydie Honorine. Power. Published at Friday, December 22nd 2017, 17:54:13 PM. Another characteristic of any linear regulator is that it requires a finite amount of time to "correct" the output voltage after a change in load current demand. This "time lag" defines the characteristic called transient response, which is a measure of how fast the regulator returns to steady-state conditions after a load change.
By Bertille Solange. Circuit. Published at Friday, December 22nd 2017, 17:48:48 PM. These are commonly termed as IC’s. They are usually in form of chips and microchips. This is a set of multiple electronic circuits on a small semiconductor device (normally silicon). With the advancement of technology, these IC’s prove to be extremely beneficial. They are present in any electronic device you can name. From computers, mobiles to other digital appliances you have multiple IC’s present in them. Their main components are a combination of Diodes, transistors and microprocessors. The microprocessors provide memory to the device. With the help of the microprocessor the electronic devices can perform logical or protocol applications.
By Madeleine Catherine. Diagram. Published at Friday, December 22nd 2017, 15:33:09 PM. A wiring diagram is sometimes helpful to illustrate how a schematic can be realized in a prototype or production environment. A proper wiring diagram will be labeled and show connections in a way that prevents confusion about how connections are made. Typically they are designed for end-users or installers. They focus on connections rather than components
By Cyrielle Marjolaine. Diagram. Published at Friday, December 22nd 2017, 15:11:58 PM. Now’s the fun stuff. Completing an electrical engineering degree and then getting a job in the field means you will see a lot a lot a lot of these schematics. It’s important to understand exactly what is going on with these. While they can (and will) get very complex, these are just a few of the common graphics to get your footing on.
By Bertille Solange. Diagram. Published at Friday, December 22nd 2017, 15:03:02 PM. Sometimes, to make schematics more legible, we’ll give a net a name and label it, rather than routing a wire all over the schematic. Nets with the same name are assumed to be connected, even though there isn’t a visible wire connecting them. Names can either be written directly on top of the net, or they can be “tags”, hanging off the wire.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.