By Cyrielle Marjolaine. Diagram. Publised at Monday, November 20th 2017, 08:59:07 AM. Now’s the fun stuff. Completing an electrical engineering degree and then getting a job in the field means you will see a lot a lot a lot of these schematics. It’s important to understand exactly what is going on with these. While they can (and will) get very complex, these are just a few of the common graphics to get your footing on.
By Jessica Mireille. Circuit. Published at Monday, December 18th 2017, 05:40:39 AM. Many different types of components and devices can be found in modern circuits, including resistors, capacitors, and inductors, semiconductor devices like diodes, transistors, and integrated circuits, transducers like microphones, light sensors and motions sensors, actuators like motors and solenoids, and various other devices like heating and lighting elements. Devices in a circuit are connected to one another by means of electrical conductors, or wires. These wires can move electric currents between various points in a circuit. Once a wire connects two or more devices, the wire and all attached device connectors are said to form a single circuit node or net. Any electrical activity on a given net is communicated to all devices attached to the net. Certain nets provide electric power to devices, and other nets carry information between devices. Nets that carry information are called signals, and signals transport information encoded as voltage levels around a circuit. Signal nets typically use smaller conductors, and transport very small currents. Nets that carry power are called supply rails (or just supplies) and supply rails transport electric power around a circuit. Power nets typically use much larger conductors that signal nets, because they must transport larger currents.
By Lydie Honorine. Diagram. Published at Monday, December 18th 2017, 05:16:38 AM. Production circuit boards typically start out as thin sheets of fiberglass (about 1mm thick) that are completely covered on both sides with very thin sheets of metal (typically copper). A "standard" circuit board might use a 1 ounce copper process, which means that one ounce of copper is evenly spread across 1 square foot of circuit board. During the manufacturing process, wire patterns are "printed" onto the copper surfaces using a compound that resists etching (hence the name Printed Circuit Board or PCB). The boards are subjected to a chemical etching process that removes all exposed copper. The remaining, un-etched copperforms wires that will interconnect the circuit board components, and small pads that define the regions where component leads will be attached.
By Madeleine Catherine. Diagram. Published at Monday, December 18th 2017, 04:49:04 AM. In a PCB that uses through-hole technology, holes are drilled through the pads so that component leads can be inserted and then fastened (soldered) in place. In a PCB that uses surface-mount technology, component leads are soldered directly to the pads on the surface. Each set of pads (or holes) in the PCB is intended to receive a particular component. To identify which component must be loaded where, reference designators are printed on the circuit board immediately adjacent to the pads using a silk-screen process. A parts list links a designated set of pads to a physical component by describing the component and assigning it a particular reference designator. The reference designators guide assemblers and testers when they are working with the PCB. Many components must be placed into the PCB in a particular orientation. By convention, components that require a particular orientation have one lead designated as pin 1. On the PCB, a square pad or silkscreen indicator typically denotes pin 1.
By Valentine Sybille. Circuit. Published at Monday, December 18th 2017, 04:45:11 AM. When multiple components are connected in parallel, the voltage drop is the same across all components. When multiple components are connected in series, the total voltage is the sum of the voltages across each component. These two statements can be generalized as Kirchoff’s Voltage Law (KVL), which states that the sum of voltages around any closed loop (e.g. starting at one node, and ending at the same node) is zero.
By Cyrielle Marjolaine. Circuit. Published at Sunday, December 17th 2017, 15:08:00 PM. Double-layer or double-sided PCBs have a base material with a thin layer of conductive metal, like copper, applied to both sides of the board. Holes drilled through the board allow circuits on one side of the board to connect to circuits on the other.
By Bertille Solange. Power. Published at Sunday, December 17th 2017, 14:30:46 PM. Load regulation refers to the ability of a voltage regulator to maintain a constant voltage as the load current varies and is expressed as a percentage. Ideally, the load regulation would be zero percent meaning that the output voltage is perfectly independent of the load current. The equation for load regulation is as follows.
By Jessica Mireille. Circuit. Published at Sunday, December 17th 2017, 11:52:33 AM. Surface mount PCBs do not utilize wires as connectors. Instead, many small leads are soldered directly to the board, meaning that the board itself is used as a wiring surface for the different components. This allows circuits to be completed using less space, freeing up space to allow the board to complete more functions, usually at higher speeds and a lighter weight than a through-hole board would allow.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.