By Bertille Solange. Circuit. Publised at Thursday, October 05th 2017, 10:31:38 AM. We all know about electricity. It is the flow electrons. Hence the word electricity is derived from the word electrons. A battery itself doesn’t work, if you hold it up in air, there would be no passage of electric current. Hence you need a circuit. In Simple terms an electronic circuit is a closed pathway for electrons to flow.
By Jessica Mireille. Diagram. Published at Thursday, December 21st 2017, 05:51:28 AM. There are drawing programs, and there are schematic capture programs. All schematic capture programs will produce output for inclusion in publications. However, these programs have different goals, and it shows. Rarely is the output of a schematic capture program really suitable for publication; often it is not even readable, or cannot be scaled. Engineers who really want to have a useful schematic drawing of a circuit usually redraw the circuit in a general drawing program, which can be both tedious and prone to introducing new errors.
By Madeleine Catherine. Circuit. Published at Thursday, December 21st 2017, 03:40:56 AM. A capacitor is a device that stores energy in the form of voltage. The most common form of capacitors is made of two parallel plates separated by a dielectric material. Charges of opposite polarity can be deposited on the plates, resulting in a voltage V across the capacitor plates. Capacitance is a measure of the amount of electrical charge required to build up one unit of voltage across the plates.
By Bertille Solange. Diagram. Published at Thursday, December 21st 2017, 01:58:02 AM. Starting to make sense? These are the basics and may even seem obvious or intuitive to you, such as the wires and if they are connected. Whenever you determine your specific field of electrical engineering, you may see more complex diagrams and symbols. You’ll learn also that different countries use different symbols. For example, of the two symbols for resistors above, the first one is used in the U.S., while the second is used in Europe. You will also learn about the various symbols used for switches, other power supplies, inductors, meters, lamps, LEDs, transistors, antennas, and much more.
By Cyrielle Marjolaine. Circuit. Published at Wednesday, December 20th 2017, 22:23:03 PM. If the components of the circuit are connected in one single path is it termed as series. The same current would flow through all the components while the voltage would differ from one component to another. For example you have lit three lamps in series to the same power source, the first one would receive more voltage than the last.
By Madeleine Catherine. Diagram. Published at Wednesday, December 20th 2017, 21:12:59 PM. In a digital circuit, power supply voltage levels are constrained to two distinct values – “logic high voltage” (called LHV or Vdd) and “logic low voltage” (called LLV or GND). The GND node in any circuit is the universal reference voltage against which all other voltages are measured (in modern digital circuits, GND is typically the lowest voltage in the circuit). In a schematic, it is often difficult to show lines connecting all GND nodes; rather, any nodes labeled GND are assumed to be connected into the same node. Often, a downward pointing triangle symbol, is attached to a GND node in addition to (or instead of) the GND label. The Vdd node in a digital circuit is typically the highest voltage, and all nodes labeled Vdd are tied together into the same node. Vdd may be thought of as the “source” of positive charges in a circuit, and GND may be thought of as the “source” of negative charges in a circuit. In modern digital systems, Vdd and GND are separated by anywhere from 1 to 5 volts. Older or inexpensive circuits typically use 5 volts, while newer circuits use 1-3 volts.
By Jessica Mireille. Circuit. Published at Wednesday, December 20th 2017, 20:16:55 PM. These are commonly termed as IC’s. They are usually in form of chips and microchips. This is a set of multiple electronic circuits on a small semiconductor device (normally silicon). With the advancement of technology, these IC’s prove to be extremely beneficial. They are present in any electronic device you can name. From computers, mobiles to other digital appliances you have multiple IC’s present in them. Their main components are a combination of Diodes, transistors and microprocessors. The microprocessors provide memory to the device. With the help of the microprocessor the electronic devices can perform logical or protocol applications.
By Lydie Honorine. Diagram. Published at Wednesday, December 20th 2017, 19:32:12 PM. Wiring diagrams use standard symbols for wiring devices, usually different from those used on schematic diagrams. The electrical symbols not only show where something is to be installed, but also what type of device is being installed. For example, a surface ceiling light is shown by one symbol, a recessed ceiling light has a different symbol, and a surface fluorescent light has another symbol. Each type of switch has a different symbol and so do the various outlets. There are symbols that show the location of smoke detectors, the doorbell chime, and thermostat. On large projects symbols may be numbered to show, for example, the panel board and circuit to which the device connects, and also to identify which of several types of fixture are to be installed at that location.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.