By Bertille Solange. Circuit. Publised at Thursday, October 05th 2017, 10:31:38 AM. Electric circuits use electric power to perform some function, like energize a heating or lighting element, turn a motor, or create an electromagnetic filed. Electronic circuits differ from electric circuits in that they use devices that can themselves be controlled by other electric signals. Restated, electronic circuits are built from devices that use electricity to control electricity. Most electronic circuits use signals that are within 5 to 10 volts of ground; most circuits built within the past several years use signals that are within 3 to 5 volts from ground. Some electronic circuits represent information encoded as continuous voltage levels that can wander between the high and low voltage supply rails – these are called analog circuits. As an example, a sound pressure level transducer (i.e. a microphone) might drive a signal between 0V and 3.3V in direct proportion to the detected sound pressure level. In this case, the voltage signal output from the microphone is said to be an analog ifthe sound pressure wave itself. Other circuits use only two distinct voltage levels to represent information. Most often, these two voltage levels use the same voltages supplied by the power rails. In these circuits, called digital circuits, all information must be represented as binary numbers, with a signal at 0V (or ground) representing one kind of information, and a signal at 3.3V (or whatever the upper voltage supply rail provides) representing the other kind of information. In this series of modules, we will confine our discussions to digital circuits.
By Cyrielle Marjolaine. Circuit. Published at Saturday, December 30th 2017, 17:29:18 PM. Surface mount PCBs do not utilize wires as connectors. Instead, many small leads are soldered directly to the board, meaning that the board itself is used as a wiring surface for the different components. This allows circuits to be completed using less space, freeing up space to allow the board to complete more functions, usually at higher speeds and a lighter weight than a through-hole board would allow.
By Valentine Sybille. Car Wiring. Published at Saturday, December 30th 2017, 13:36:45 PM. All of the ground wires in the cockpit can be run to the forward frame grounding post and the battery ground can be run to the frame at the rear or wherever you mount the battery. The exception in his case is the ignition ground, which he runs separate from the other ground wires directly to the battery ground.
By Valentine Sybille. Car Wiring. Published at Saturday, December 30th 2017, 12:56:44 PM. When fitting extra accessories, such as a rear window heater which consumes a heavy current, always wire it through the ignition switch. Some ancillary components can be operated without the ignition turned on by turning the switch to the "auxiliary" position. A radio is usually wired through this switch, so that it can be played with the engine off.
By Cyrielle Marjolaine. Car Wiring. Published at Saturday, December 30th 2017, 12:48:04 PM. This is called a negative earth system, and when buying an electrical accessory a radio, for example check that it is of a type suitable for your cars system. Fitting a radio with the incorrect polarity will damage the set, but most car radios have an external switch for setting the polarity to suit that of the car. Switch to the correct setting before fitting.
By Charlotte Myriam. Car Wiring. Published at Saturday, December 30th 2017, 08:57:08 AM. Plan out your wiring. Choose the path the wires will follow. Choose the locations of all of your switches, gauges, ignition box, battery, and charging posts. If your past layout was deficient, now is the time to rethink the entire plan.
By Alix Loane. Car Wiring. Published at Saturday, December 30th 2017, 08:48:04 AM. Modern cars often need room for many wires in confined spaces. Some manufacturers now use printed circuits instead of bundles of wires, particularly at the rear of the instrument panel. Printed circuits are plastic sheets on which copper tracks have been "printed". Components are plugged directly into the tracks. A few modern cars have flexible printed circuits. The copper tracks are printed in ribbons of flexible plastic, which replace the whole wiring system.
By Bertille Solange. Car Wiring. Published at Saturday, December 30th 2017, 08:25:15 AM. The same is true of the ignition wire and the coil wire. These should not be closer than 1 inch. Many teams will tie-wrap these two wires together, which is a very bad idea. The pulse from the coil wire is very strong and interferes with the ignition signal.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.