By Bertille Solange. Circuit. Publised at Thursday, October 05th 2017, 10:31:38 AM. A single-layer or single-sided PCB is one that is made out of a single layer of base material or substrate. One side of the base material is coated with a thin layer of metal. Copper is the most common coating due to how well it functions as an electrical conductor. Once the copper base plating is applied, a protective solder mask is usually applied, followed by the last silk-screen to mark out all of the elements on the board.
By Madeleine Catherine. Diagram. Published at Friday, January 05th 2018, 00:00:29 AM. A digital circuit is constructed of a power supply, devices, and conduction nets. Some nets provide circuit inputs from the “outside world”; in a schematic, these input nets are generally shown entering the left side of component and/or the overall circuit. Other nets present circuit outputs to the outside world; these nets are generally shown exiting the schematic on the right. In the sample schematic below, circuit components are shown as arbitrary shapes, nets are shown as lines, and inputs and outputs are denoted by connector symbols.
By Cyrielle Marjolaine. Motor. Published at Thursday, January 04th 2018, 17:04:00 PM. The effect of rewiring the motor from full-winding to half-winding while keeping the same power supply voltage. A half-winding connected motor delivers twice as much power as a full-winding connection at a given power supply voltage. This is because full-winding inductance is four times higher than half-winding inductance.
By Valentine Sybille. Diagram. Published at Thursday, January 04th 2018, 16:58:49 PM. Voltage nodes are single-terminal schematic components, which we can connect component terminals to in order to assign them to a specific voltage level. These are a special application of net names, meaning all terminals connected to a like-named voltage node are connected together.
By Charlotte Myriam. Diagram. Published at Thursday, January 04th 2018, 15:13:37 PM. If there’s something on a schematic that just doesn’t make sense, try finding a datasheet for the most important component. Usually the component doing the most work on a circuit is an integrated circuit, like a microcontroller or sensor. These are usually the largest component, oft-located at the center of the schematic.
By Lydie Honorine. Circuit. Published at Thursday, January 04th 2018, 12:58:36 PM. An electric current is defined as free flow of electrons and the motivating force behind that free flow of electrons is called Voltage. Voltage is the measurement of potential energy that would move the electrons between two points. Voltage is the push that the electrons require to move within a circuit. Voltage is measured by Volt and Current is measured by Ampere.
By Sasha Sara. Diagram. Published at Thursday, January 04th 2018, 11:09:44 AM. Wiring diagrams use standard symbols for wiring devices, usually different from those used on schematic diagrams. The electrical symbols not only show where something is to be installed, but also what type of device is being installed. For example, a surface ceiling light is shown by one symbol, a recessed ceiling light has a different symbol, and a surface fluorescent light has another symbol. Each type of switch has a different symbol and so do the various outlets. There are symbols that show the location of smoke detectors, the doorbell chime, and thermostat. On large projects symbols may be numbered to show, for example, the panel board and circuit to which the device connects, and also to identify which of several types of fixture are to be installed at that location.
By Valentine Sybille. Circuit. Published at Thursday, January 04th 2018, 07:29:50 AM. For DC signals, the linearity of the system implies that H is independent of Vin. For dynamic signals, the transfer function cannot in general be described simply. However, if the input is a sinusoidal signal then the output must also be a sinusoidal signal with the same frequency but possibly a different amplitude and phase. In other words, a linear system can only modify the amplitude and phase of a sinusoidal input.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.