By Madeleine Catherine. Diagram. Publised at Saturday, December 23rd 2017, 20:46:14 PM. There are two commonly used capacitor symbols. One symbol represents a polarized (usually electrolytic or tantalum) capacitor, and the other is for non-polarized caps. In each case there are two terminals, running perpendicularly into plates. The symbol with one curved plate indicates that the capacitor is polarized. The curved plate represents the cathode of the capacitor, which should be at a lower voltage than the positive, anode pin. A plus sign might also be added to the positive pin of the polarized capacitor symbol.
By Valentine Sybille. Circuit. Publised at Saturday, December 23rd 2017, 04:38:48 AM. Ohm’s law states that the current through a conductor between two points is directly proportional to the potential difference across those two points. It means that more the resistance lesser current would flow. I=V/R This would apply to any component of a circuit. For example conductors would increase the current flow and the inductors would decrease it.
By Madeleine Catherine. Circuit. Published at Monday, December 25th 2017, 12:47:39 PM. The concept of complex impedance introduces a unified representation for resistors, capacitors, and inductors, whereby a circuit’s frequency response from input to output can be determined using KVL and KCL, where each element is assigned the appropriate impedance. The key assumption to this point is that the input to the circuit must consist solely of DC and/or sinusoidal signals. Now, this analysis is be extended to include arbitrary input signals by using the mathematical techniques of Laplace transforms.
By Cyrielle Marjolaine. Motor. Published at Monday, December 25th 2017, 12:27:21 PM. If one changes the power supply voltage, then a new family of speed-torque curves result. As an example, if the power supply voltage is doubled then a new curve is generated; the curve now has twice the torque at any given speed in region 2. Since power equals torque times speed, the motor now generates twice as much power as well.
By Sasha Sara. Diagram. Published at Monday, December 25th 2017, 11:54:38 AM. A schematic shows connections in a circuit in a way that is clear and standardized. It is a way of communicating to other engineers exactly what components are involved in a circuit as well as how they are connected. A good schematic will show component names and values, and provide labels for sections or components to help communicate the intended purpose. Note how connections on wires (or "nets") are shown using dots and non-connections are shown without a dot.
By Cyrielle Marjolaine. Amplifier. Published at Monday, December 25th 2017, 10:10:23 AM. Then the lower part of the output waveform which is below this 0.7v window will not be reproduced accurately resulting in a distorted area of the output waveform as one transistor turns “OFF” waiting for the other to turn back “ON”. The result is that there is a small part of the output waveform at the zero voltage cross over point which will be distorted. This type of distortion is called Crossover Distortion and is looked at later on in this section.
By Sasha Sara. Circuit. Published at Monday, December 25th 2017, 07:47:25 AM. First let’s understand the difference between these two terms. While electrical is the basis of everything, electronic is a subset of electrical. An electrical circuit deals with just the flow of electrons and has components like resistors, inductors and capacitors and uses Alternating Current Source; while electronic circuit deals with the transformation of current and controlling the motion of the electrons and uses Direct Current Source. An electrical circuit is termed as Passive because it doesn’t have any such component that reacts to the current/voltage that passes through them and electronic circuit is called active because of the additional components like diode or a transformer that react to the current/voltage that passes through.
By Bertille Solange. Amplifier. Published at Monday, December 25th 2017, 06:04:45 AM. First and probably the most important thing I learned is all grounds should not go directly to the chassis. This seems contrary to logic. A little side trip into electricity and conductors is appropriate now. Any conductor has some finite resistance and anytime some current is passed through it a voltage will be correspondingly created. Actually the voltage is first, but in this case we want to concentrate on the current. In a typical piece of audio equipment (most everything else as well) there are usually three distinct ground circuits. The first is obvious, the signal ground, the second is the power supply ground and third and often ignored is the case or chassis ground. Each has a particular function and all interact. The signal ground usual and primary function is to provide a return path for the audio. Likewise the power supply ground is the return path for the power used by the circuitry. The case ground I will cover a bit later. Remembering that anytime current flows through a conductor it will cause a voltage, let us see what happens if you mix the signal and power grounds. Each will generate a proportional corresponding voltage. So for an example: the conductor is a piece of wire that has a 1 ohm resistance, the signal voltage (and thus its return) has one millivolt (mV)of amplitude and the power supply is causing a flow of 100 milliamperes (mA) through the wire. The contribution to the voltages on the conductor is then, 1 mV for the signal and 0.1 Ampere times 1 ohm equals 100 mV for the power - see Ohm Law for equations. Since it is really unlikely that the power is perfectly clean DC it will contaminate the signal with hum and noise. Even a 1% noise level in the DC will result in a noise voltage equal to the signal voltage. I grant that this is a gross simplification, but it does illustrate the situation. So my rule number one is to absolutely avoid having any ground conductor handling both signal and power. So how do you do this? I find that a sort of modular arrangement is best. This does not mean that the physical components ca not be on the same board though. What it does mean is that the power supply is wired independently from the active signal portion. Eventually these grounds need to connect, but I will get to that later.
By Valentine Sybille. Circuit. Published at Monday, December 25th 2017, 05:39:30 AM. A basic understanding of electronic circuits is important even if the designer does not intend to become a proficient electrical engineer. In many real-life engineering projects, it is often necessary to communicate, and also negotiate, specifications between engineering teams having different areas of expertise. Therefore, a basic understanding of electronic circuits will allow the mechanical engineer to evaluate whether or not a given electrical specification is reasonable and feasible.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.