By Cyrielle Marjolaine.

Power. Publised at Tuesday, December 19th 2017, 11:49:21 AM. The Standard regulator is usually best for AC-powered applications, where the low cost and high load current make it the ideal choice. In AC-powered applications, the voltage across the regulator is usually at least 3V or more, so dropout voltage is not critical.

By Sasha Sara.

Motor. Published at Monday, December 18th 2017, 08:03:25 AM. An ideal step motor would have zero mechanical friction, its torque would be proportional to ampere-turns and its only electrical characteristic would be inductance. Ampere-turns simply mean that torque is proportional to the number of turns of wire in the motor’s stator multiplied by the current passing through those turns of wire.

By Lydie Honorine.

Circuit. Published at Monday, December 18th 2017, 06:44:29 AM. Impedance essentially can be viewed as frequency-dependent resistance. While resistance of a circuit is the instantaneous ratio between voltage and current, impedance of a circuit is the ratio between voltage and current for steady-state sinusoidal signals, which can vary with of frequency. As the later parts of this section will show, the voltage and current caused by applying a steady-state sinusoidal signal to any combination of resistors, capacitors, and inductors, are related by a constant factor and a phase shift. Therefore, impedance can be expressed by a complex constant using an extended version Ohm’s law.

By Charlotte Myriam.

Diagram. Published at Monday, December 18th 2017, 06:12:46 AM. A digital circuit requires a power supply to provide a constant and stable source of electric power to all devices. As discussed above, electric power is derived from the basic electrical forces that charged particles (e.g., protons and electrons) exert on one another – namely, electrons are repelled by other electrons, and attracted to more electrically positive areas where there are relatively fewer electrons. The vast majority of charged particles are found in ordinary matter bound in electrically neutral atomic structures (that is, most particles are found in structures that have an equal number of positive and negative particles). Some electrically neutral conducting materials (like metals) contain electrons that are not so tightly bound to their host atoms. If a voltage source is applied to these materials, the lightly bound electrons will move away from the concentrated source of electrons on the negative side of the supply towards the electrically positive side of the supply. A “power supply” in a digital circuit provides a local, contained imbalance of electrons that provides a voltage source that can do useful work, such as transmitting information through a conductor from one device to another. A digital circuit allows a controlled flow of electrons from of the negative to positive side of the power supply, but only via the paths designed into the circuit. As electrons flow to and from the devices in a given circuit, they can change device properties in useful ways.

By Valentine Sybille.

Diagram. Published at Monday, December 18th 2017, 05:53:49 AM. Sometimes, to make schematics more legible, we’ll give a net a name and label it, rather than routing a wire all over the schematic. Nets with the same name are assumed to be connected, even though there isn’t a visible wire connecting them. Names can either be written directly on top of the net, or they can be “tags”, hanging off the wire.

By Madeleine Catherine.

Power. Published at Monday, December 18th 2017, 05:46:00 AM. The maximum current that a linear regulator can supply to a load is specified on the data sheet. Many regulators (and most LDO regulators) specify only a single value of maximum current. This value is guaranteed for any input/output voltage within the maximum ratings for the part.

By Jessica Mireille.

Circuit. Published at Monday, December 18th 2017, 05:40:39 AM. The concept of complex impedance introduces a unified representation for resistors, capacitors, and inductors, whereby a circuit’s frequency response from input to output can be determined using KVL and KCL, where each element is assigned the appropriate impedance. The key assumption to this point is that the input to the circuit must consist solely of DC and/or sinusoidal signals. Now, this analysis is be extended to include arbitrary input signals by using the mathematical techniques of Laplace transforms.

By Lydie Honorine.

Diagram. Published at Monday, December 18th 2017, 05:16:38 AM. Knowing how to read circuits is a very useful skill that will help you out all the time. especially if you start messing around with building little electronics projects.

Recent post

- Ih 284 Tractor Wiring Diagram
- John Deere Model 50 Engine Diagram
- Dodge Dart Steering Column Wiring
- Honda Odyssey Transmission Wiring Diagrams
- Jeep Cj Wiring Diagram For Starter
- John Deere 2120 Wiring Diagram
- John Deere L118 Wiring Schematics
- Diagram Rover Engine Discovery 2013
- Light Fixture Dimmer Wire Diagram
- John Deere Model A Engine Diagram

Category

Monthly Archives

Static Page

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z - 0 1 2 3 4 5 6 7 8 9

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z - 0 1 2 3 4 5 6 7 8 9

Altrushare - Wiring Diagram Gallery

Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.