By Lydie Honorine. Diagram. Publised at Sunday, November 05th 2017, 20:23:44 PM. Wiring diagrams use standard symbols for wiring devices, usually different from those used on schematic diagrams. The electrical symbols not only show where something is to be installed, but also what type of device is being installed. For example, a surface ceiling light is shown by one symbol, a recessed ceiling light has a different symbol, and a surface fluorescent light has another symbol. Each type of switch has a different symbol and so do the various outlets. There are symbols that show the location of smoke detectors, the doorbell chime, and thermostat. On large projects symbols may be numbered to show, for example, the panel board and circuit to which the device connects, and also to identify which of several types of fixture are to be installed at that location.
By Bertille Solange. Diagram. Published at Wednesday, December 27th 2017, 00:30:05 AM. Sometimes, to make schematics more legible, we’ll give a net a name and label it, rather than routing a wire all over the schematic. Nets with the same name are assumed to be connected, even though there isn’t a visible wire connecting them. Names can either be written directly on top of the net, or they can be “tags”, hanging off the wire.
By Jessica Mireille. Power. Published at Tuesday, December 26th 2017, 23:57:09 PM. Linear regulators are simple voltage regulator circuits commonly used in electronics. This paper briefly discusses how linear regulators work, their advantages and disadvantages, variations on the linear regulator, and important datasheet parameters.
By Sasha Sara. Amplifier. Published at Tuesday, December 26th 2017, 23:51:43 PM. So at this point we have the signal and power grounds connected. Next is the chassis. There are a number of ways that we can accomplish this connection. The key thought is to maintain the shock protection while using it as an EMI shield. Sometimes it can connect directly to the ground at the input jacks. This was a fairly common practice in the earlier days of electronic equipment. These were also in many cases what I would consider lower fidelity equipment and things that did not benefit from three wire AC mains. I do not recommend this as there is the possibility of introducing the EMI noise from the chassis and AC mains earth ground into the signal path. Most methods of making the connection involve resistors, capacitors or rectifiers. I suspect all will work. My preference is for a parallel combination of a metal film resistor of about 120 ohms (1/2 Watt is fine) and a type X2 capacitor in the range of 0.1 to 0.22uF. Type X2 capacitors are rated for use with AC mains circuits. I have seen ceramics and polys used there but since they are not usually AC mains rated I strongly recommend against them. The capacitor and resistor provide sufficient isolation between the chassis and circuitry to allow the chassis to be an effective EMI shield but not induce the EMI into the active circuitry.
By Alix Loane. Circuit. Published at Tuesday, December 26th 2017, 21:47:43 PM. In some circuits, there are virtual grounds, which are nodes at the same voltage as ground, but are not connected to a power supply. When current flows into the virtual ground, the voltage at the virtual ground may change relative to the real ground, and the consequences of this situation must be analyzed carefully.
By Alix Loane. Diagram. Published at Tuesday, December 26th 2017, 21:46:31 PM. A digital circuit requires a power supply to provide a constant and stable source of electric power to all devices. As discussed above, electric power is derived from the basic electrical forces that charged particles (e.g., protons and electrons) exert on one another – namely, electrons are repelled by other electrons, and attracted to more electrically positive areas where there are relatively fewer electrons. The vast majority of charged particles are found in ordinary matter bound in electrically neutral atomic structures (that is, most particles are found in structures that have an equal number of positive and negative particles). Some electrically neutral conducting materials (like metals) contain electrons that are not so tightly bound to their host atoms. If a voltage source is applied to these materials, the lightly bound electrons will move away from the concentrated source of electrons on the negative side of the supply towards the electrically positive side of the supply. A “power supply” in a digital circuit provides a local, contained imbalance of electrons that provides a voltage source that can do useful work, such as transmitting information through a conductor from one device to another. A digital circuit allows a controlled flow of electrons from of the negative to positive side of the power supply, but only via the paths designed into the circuit. As electrons flow to and from the devices in a given circuit, they can change device properties in useful ways.
By Alix Loane. Circuit. Published at Tuesday, December 26th 2017, 21:42:25 PM. Impedance is one of the most important concepts in electronic circuits. The purpose of impedance is to generalize the idea of resistance to create a component. To capture the behavior of resistors, capacitors, and inductors, for steadystate sinusoidal signals. This generalization is motivated by the fact that as long as the circuit is linear, its behavior can be analyzed using KVL and KCL.
By Valentine Sybille. Diagram. Published at Tuesday, December 26th 2017, 20:06:46 PM. Starting to make sense? These are the basics and may even seem obvious or intuitive to you, such as the wires and if they are connected. Whenever you determine your specific field of electrical engineering, you may see more complex diagrams and symbols. You’ll learn also that different countries use different symbols. For example, of the two symbols for resistors above, the first one is used in the U.S., while the second is used in Europe. You will also learn about the various symbols used for switches, other power supplies, inductors, meters, lamps, LEDs, transistors, antennas, and much more.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.