By Lydie Honorine. Diagram. Publised at Sunday, November 05th 2017, 20:23:44 PM. In contrast to digital circuits, analog circuits use signals whose voltage levels are not constrained to two distinct levels, but instead can assume any value between Vdd and GND. Many input devices, particularly those using electronic sensors (e.g., microphones, cameras, thermometers, pressure sensors, motion and proximity detectors, etc.) produce analog voltages at their outputs. In modern electronic devices, it is likely that such signals will be converted to digital signals before they are used within the device. For example, a digital voice-memo recording device uses an analog microphone circuit to convert sound pressure waves into voltage waves on an internal circuit node. A special circuit called an analog-to-digital converter, or ADC, converts that analog voltage to a binary number that can be represented as a bus in a digital circuit. An ADC functions by taking samples of the input analog signal, measuring the magnitude of the input voltage signal (usually with reference to GND), and assigning a binary number to the measured magnitude. Once an analog signal has been converted to a binary number, a bus can carry that digital information around a circuit. In a similar manner, digital signals can be reconstituted into analog signals using a digital-to-analog converter. Thus, a binary number that represents a sample of an audio waveform can be converted to an analog signal that can, for example, drive a speaker.
By Madeleine Catherine. Circuit. Publised at Sunday, December 17th 2017, 00:43:41 AM. Most electronic circuits can be represented as a system with an input and an output. The input signal is typically a voltage that is generated by a sensor or by another circuit. The output signal is also
By Madeleine Catherine. Circuit. Publised at Tuesday, December 26th 2017, 07:11:55 AM. Surface mount PCBs do not utilize wires as connectors. Instead, many small leads are soldered directly to the board, meaning that the board itself is used as a wiring surface for the different components. This allows circuits to be completed using less space, freeing up space to allow the board to complete more functions, usually at higher speeds and a lighter weight than a through-hole board would allow.
By Madeleine Catherine. Car Wiring. Published at Friday, January 12th 2018, 06:20:13 AM. You have a lot of time in the off-season and for your team, designate a qualified person to be in charge of the wiring and the process of rewiring the car as well as being the pointman for mid-season troubleshooting of electrical problems. Don’t assume everything will be OK for next season with what you have, take the effort to make sure. It’s so much fun when things don’t go wrong.
By Madeleine Catherine. Motor. Published at Thursday, January 11th 2018, 18:44:58 PM. A real step motor has losses that modify the ideal speed-torque curve. The most important effect is the contribution of detent torque. Detent torque is usually specified in the motor datasheet. It is always a loss when the motor is turning and the power consumed to overcome it is proportional to speed. In other words, the faster the motor turns the greater the detent torque contributes power loss at the motor’s output shaft. This power loss is proportional to speed and must be subtracted from the ideal, flat output power curve past the corner speed. This now constitutes a practical speed-torque curve.
By Lydie Honorine. Car Wiring. Published at Thursday, January 11th 2018, 18:31:10 PM. Plan out your wiring. Choose the path the wires will follow. Choose the locations of all of your switches, gauges, ignition box, battery, and charging posts. If your past layout was deficient, now is the time to rethink the entire plan.
By Madeleine Catherine. Circuit. Published at Thursday, January 11th 2018, 15:49:52 PM. A collection of electronic components that have been assembled and interconnected to perform a given function is commonly referred to as a circuit. The word circuit derives from the fact that electric power must flow from the positive terminal of a power source through one or more electronic devices and back to the negative terminal of a power source, thereby forming a circuit. If the connections between an electronic device and either the positive or negative terminals of a power supply are interrupted, the circuit will be broken and the device will not function.
By Bertille Solange. Car Wiring. Published at Thursday, January 11th 2018, 10:13:49 AM. The most common type of fuse is a short length of thin wire enclosed in a heatproof casing often glass. The size of the fuse wire is the thinnest that can carry the normal current of the circuit without overheating, and it is rated in amps.
By Valentine Sybille. Car Wiring. Published at Thursday, January 11th 2018, 08:14:17 AM. Most are wired through the ignition switch, so that they work only when the ignition is switched on. This prevents you accidentally leaving something switched on which might cause the battery to go flat. The side and tail lights, however, which you may need to leave on when the car is parked, are always wired independently of the ignition switch.
By Bertille Solange. Circuit. Published at Thursday, January 11th 2018, 05:22:15 AM. If the components of the circuit are connected in one single path is it termed as series. The same current would flow through all the components while the voltage would differ from one component to another. For example you have lit three lamps in series to the same power source, the first one would receive more voltage than the last.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.