By Cyrielle Marjolaine.

Motor. Publised at Thursday, June 08th 2017, 14:32:37 PM. To make your own power supply you must have three key components: a transformer, bridge rectifier, and filter capacitor. The transformer’s current rating must be sufficient to adequately run all motors that will be run from it using the above current formula. The DC output voltage will be 1.4 times the transformer’s AC voltage rating of the secondary. For example, a 24VAC transformer secondary will provide about 34VDC at the output of the supply. The bridge rectifier’s voltage and current ratings must exceed what the supply will deliver. Finally the minimum filter capacitor size must be calculated.

By Cyrielle Marjolaine.

Circuit. Published at Sunday, November 19th 2017, 23:05:33 PM. Electronic signals are represented either by voltage or current. The timedependent characteristics of voltage or current signals can take a number of forms including DC, sinusoidal (also known as AC), square wave, linear ramps, and pulsewidth modulated signals. Sinusoidal signals are perhaps the most important signal forms since once the circuit response to sinusoidal signals are known, the result can be generalized to predict how the circuit will respond to a much greater variety of signals using the mathematical tools of Fourier and Laplace transforms.

By Valentine Sybille.

Circuit. Published at Sunday, November 19th 2017, 22:33:06 PM. Electronic signals are represented either by voltage or current. The timedependent characteristics of voltage or current signals can take a number of forms including DC, sinusoidal (also known as AC), square wave, linear ramps, and pulsewidth modulated signals. Sinusoidal signals are perhaps the most important signal forms since once the circuit response to sinusoidal signals are known, the result can be generalized to predict how the circuit will respond to a much greater variety of signals using the mathematical tools of Fourier and Laplace transforms.

By Alix Loane.

Circuit. Published at Sunday, November 19th 2017, 22:10:34 PM. Impedance essentially can be viewed as frequency-dependent resistance. While resistance of a circuit is the instantaneous ratio between voltage and current, impedance of a circuit is the ratio between voltage and current for steady-state sinusoidal signals, which can vary with of frequency. As the later parts of this section will show, the voltage and current caused by applying a steady-state sinusoidal signal to any combination of resistors, capacitors, and inductors, are related by a constant factor and a phase shift. Therefore, impedance can be expressed by a complex constant using an extended version Ohm’s law.

By Madeleine Catherine.

Diagram. Published at Sunday, November 19th 2017, 21:57:33 PM. Voltage nodes are single-terminal schematic components, which we can connect component terminals to in order to assign them to a specific voltage level. These are a special application of net names, meaning all terminals connected to a like-named voltage node are connected together.

By Charlotte Myriam.

Power. Published at Sunday, November 19th 2017, 20:59:18 PM. In shunt regulation a resistor is typically placed in series with the load and the unregulated voltage. The resistor is small enough so that the load could always receive somewhat more than the maximum current it would ever need. The shunt regulator is placed across the load and conducts excess current around the load such that the voltage across the load remains a constant as the load draws the actual current at any given time. A common shunt regulator is a Zener diode which is an example of an open loop system. Feedback control can also be used to drive the current through the control element (a transistor) across the load. Shunt regulators are generally only used for low power applications because they can be very inefficient. However, shunt regulators have an inherent fault current limiting feature and also can regulate even if the load is forcing current into the regulator rather than drawing current from it. Shunt regulators also have an interesting feature that the input current is constant – independent of load current (except if a load fault occurs – but that is a special case not in normal operation). Thus shunt regulators are very good at isolating a load with rapid and large current fluctuations.

By Sasha Sara.

Motor. Published at Sunday, November 19th 2017, 20:52:00 PM. The drive is a current source in the constant torque region and adds no additional phase lag. In the constant power region however, the drive is a voltage source so it introduces an additional 90 degree phase lag. The total phase lag now is 180 degrees, which is a setup for a sustained and building motor oscillation. This oscillation is commonly called mid-band instability or mid-band resonance.

By Lydie Honorine.

Diagram. Published at Sunday, November 19th 2017, 20:50:47 PM. Sometimes, to make schematics more legible, we’ll give a net a name and label it, rather than routing a wire all over the schematic. Nets with the same name are assumed to be connected, even though there isn’t a visible wire connecting them. Names can either be written directly on top of the net, or they can be “tags”, hanging off the wire.

Recent post

- Ih 284 Tractor Wiring Diagram
- John Deere Model 50 Engine Diagram
- Dodge Dart Steering Column Wiring
- Honda Odyssey Transmission Wiring Diagrams
- Jeep Cj Wiring Diagram For Starter
- John Deere 2120 Wiring Diagram
- John Deere L118 Wiring Schematics
- Diagram Rover Engine Discovery 2013
- Light Fixture Dimmer Wire Diagram
- John Deere Model A Engine Diagram

Category

Monthly Archives

Static Page

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z - 0 1 2 3 4 5 6 7 8 9

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z - 0 1 2 3 4 5 6 7 8 9

Altrushare - Wiring Diagram Gallery

Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.