By Cyrielle Marjolaine. Motor. Publised at Thursday, June 08th 2017, 14:32:37 PM. If more than one drive is being operated from the power supply this is not a problem since the other drive(s) will absorb this current for its needs, unless it is decelerating as well. For this case or for a single drive it may be necessary to place a voltage clamp across the power supply in the form of a Zener diode. The voltage of this diode must be greater than the maximum expected power supply voltage, yet low enough to protect the drive. A good choice would be either 82 volts or 91 volts as standard values.
By Jessica Mireille. Car Wiring. Published at Sunday, December 31st 2017, 12:05:54 PM. Apart from the main charging, starting and ignition circuits, there are other circuits that power lights, electric motors, the sensors and gauges of electrical instruments, heating elements, magnetically operated locks, the radio and so on. All Circuits are opened and closed either by switches or by relays - remote switches operated by electromagnets.
By Madeleine Catherine. Motor. Published at Sunday, December 31st 2017, 11:43:49 AM. At this point it is important to introduce the concept of overdrive ration. This is the ration between the power supply voltage and the motor’s rated voltage. An empirically derived maximum is 25:1, meaning the power supply voltage should never exceed 25 times the motor’s rated voltage or 32 times the square root of motor inductance. Below is a graph of measured iron losses for a 4A, 3V motor. Notice in Figure 16 how the iron losses range from insignificant to being the major cause of heating in the motor compared to a constant 12W copper loss (4A times 3V).
By Cyrielle Marjolaine. Diagram. Published at Sunday, December 31st 2017, 06:27:36 AM. Variable resistors and potentiometers each augment the standard resistor symbol with an arrow. The variable resistor remains a two-terminal device, so the arrow is just laid diagonally across the middle. A potentiometer is a three-terminal device, so the arrow becomes the third terminal (the wiper).
By Bertille Solange. Diagram. Published at Saturday, December 30th 2017, 23:20:44 PM. Truly expansive schematics should be split into functional blocks. There might be a section for power input and voltage regulation, or a microcontroller section, or a section devoted to connectors. Try recognizing which sections are which, and following the flow of circuit from input to output. Really good schematic designers might even lay the circuit out like a book, inputs on the left side, outputs on the right.
By Sasha Sara. Car Wiring. Published at Saturday, December 30th 2017, 22:08:32 PM. If certain wires are joined for a specific length, then you can create a wiring harness custom designed for your car. Then when the old season is over, you’ll have a ready-made harness to install for next year.
By Alix Loane. Diagram. Published at Saturday, December 30th 2017, 20:00:37 PM. Several different resistors are used on Digilent boards. Some are used to limit LED current, and some are used on inputs (like the button and switch circuits) to both limit the currents flowing to the main chip, and to help protect against electrostatic discharge (or ESD – more on this topic later). The resistors on the Digilent boards, like most resistors used in digital systems, are physically small because they will not encounter large voltages or currents. For these smaller resistors, the resistor value in Ohms is printed in microscopic numbers on the resistor body, not visible to the naked eye.
By Bertille Solange. Diagram. Published at Saturday, December 30th 2017, 17:52:52 PM. Wiring diagrams use standard symbols for wiring devices, usually different from those used on schematic diagrams. The electrical symbols not only show where something is to be installed, but also what type of device is being installed. For example, a surface ceiling light is shown by one symbol, a recessed ceiling light has a different symbol, and a surface fluorescent light has another symbol. Each type of switch has a different symbol and so do the various outlets. There are symbols that show the location of smoke detectors, the doorbell chime, and thermostat. On large projects symbols may be numbered to show, for example, the panel board and circuit to which the device connects, and also to identify which of several types of fixture are to be installed at that location.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.