By Bertille Solange. Circuit. Publised at Friday, June 30th 2017, 01:44:35 AM. When multiple components are connected in parallel, the voltage drop is the same across all components. When multiple components are connected in series, the total voltage is the sum of the voltages across each component. These two statements can be generalized as Kirchoff’s Voltage Law (KVL), which states that the sum of voltages around any closed loop (e.g. starting at one node, and ending at the same node) is zero.
By Lydie Honorine. Car Wiring. Published at Friday, January 19th 2018, 06:21:08 AM. The same is true of the ignition wire and the coil wire. These should not be closer than 1 inch. Many teams will tie-wrap these two wires together, which is a very bad idea. The pulse from the coil wire is very strong and interferes with the ignition signal.
By Jessica Mireille. Motor. Published at Thursday, January 18th 2018, 22:32:39 PM. A step motor is highly resonant because it is a mass-spring system. The “mass” portion is the rotor and load inertia while the “spring” portion is the restoring torque of the magnetic field that drags the rotor along. Because of this, velocity lags torque by 90 degrees.
By Bertille Solange. Circuit. Published at Monday, January 15th 2018, 19:06:47 PM. Electric circuits use electric power to perform some function, like energize a heating or lighting element, turn a motor, or create an electromagnetic filed. Electronic circuits differ from electric circuits in that they use devices that can themselves be controlled by other electric signals. Restated, electronic circuits are built from devices that use electricity to control electricity. Most electronic circuits use signals that are within 5 to 10 volts of ground; most circuits built within the past several years use signals that are within 3 to 5 volts from ground. Some electronic circuits represent information encoded as continuous voltage levels that can wander between the high and low voltage supply rails – these are called analog circuits. As an example, a sound pressure level transducer (i.e. a microphone) might drive a signal between 0V and 3.3V in direct proportion to the detected sound pressure level. In this case, the voltage signal output from the microphone is said to be an analog ifthe sound pressure wave itself. Other circuits use only two distinct voltage levels to represent information. Most often, these two voltage levels use the same voltages supplied by the power rails. In these circuits, called digital circuits, all information must be represented as binary numbers, with a signal at 0V (or ground) representing one kind of information, and a signal at 3.3V (or whatever the upper voltage supply rail provides) representing the other kind of information. In this series of modules, we will confine our discussions to digital circuits.
By Bertille Solange. Motor. Published at Monday, January 15th 2018, 17:21:59 PM. If one changes the power supply voltage, then a new family of speed-torque curves result. As an example, if the power supply voltage is doubled then a new curve is generated; the curve now has twice the torque at any given speed in region 2. Since power equals torque times speed, the motor now generates twice as much power as well.
By Alix Loane. Motor. Published at Sunday, January 14th 2018, 19:23:49 PM. The effect of setting the motor current to twice the rated value. This abuses the motor because it will dissipate four times as much heat as setting the current to its proper value. The actual increase in low-speed torque is considerably less than double because of magnetic saturation of the motor iron.
By Valentine Sybille. Motor. Published at Saturday, January 13th 2018, 16:12:10 PM. As shown earlier, motor output power is proportional to power supply voltage, doubling the voltage doubles the output power. However, iron losses outpace motor power by increasing non-linearly with increasing power supply voltage. Eventually the point is reached where the iron losses are so great that the motor cannot dissipate the heat generated. In a way this is nature’s way of keeping someone from getting 500HP from a NEMA 23 motor by using a 10kV power supply.
By Madeleine Catherine. Diagram. Published at Saturday, January 13th 2018, 10:10:30 AM. Electronic components are often assembled and interconnected on a flat surface known as a circuit board. The several types of existing circuit boards may be divided into two broad categories: those intended for prototype or experimental circuits; and those intended for production and/or commercial sale. Circuit boards used for experimental work are often referred to as breadboards or protoboards. Breadboards allow engineers to construct circuits quickly, so that they can be studied and modified until an optimal design is discovered. In a typical breadboard use, components and wires are added to a circuit in an ad hoc manner as the design proceeds, with new data and new understanding dictating the course of the design. Since breadboard circuits exist only in the laboratory, no special consideration need be given to creating reliable or simple-to-manufacture circuits – the designer can focus exclusively on the circuits behavior. In contrast, circuit boards intended for production or commercial sale must have highly reliable wires and interconnects, permanent bonds to all components, and topographies amenable to mass production and thorough testing. And further, they must be made of a material that is reliable, low-cost, and easy to manufacture. A fiberglass substratewith copper wires (etched from laminated copper sheets) has been the PCB material of choice for the past several decades. The Digilent board is a simple example of such a board. Note that most often, production circuit board designs are finalized only after extensive breadboard phases. Components are permanently affixed to production boards using the soldering process.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.