By Bertille Solange. Circuit. Publised at Friday, June 30th 2017, 01:44:35 AM. A capacitor is a device that stores energy in the form of voltage. The most common form of capacitors is made of two parallel plates separated by a dielectric material. Charges of opposite polarity can be deposited on the plates, resulting in a voltage V across the capacitor plates. Capacitance is a measure of the amount of electrical charge required to build up one unit of voltage across the plates.
By Valentine Sybille. Diagram. Published at Thursday, January 04th 2018, 16:58:49 PM. The voltage source, such as a battery, is needed in order to cause the current to flow through the circuit. In addition, there needs to be a conductive path that provides a route for the electricity to flow. Finally, a proper circuit needs a load that consumes the power.
By Charlotte Myriam. Diagram. Published at Thursday, January 04th 2018, 15:13:37 PM. A digital circuit is constructed of a power supply, devices, and conduction nets. Some nets provide circuit inputs from the “outside world”; in a schematic, these input nets are generally shown entering the left side of component and/or the overall circuit. Other nets present circuit outputs to the outside world; these nets are generally shown exiting the schematic on the right. In the sample schematic below, circuit components are shown as arbitrary shapes, nets are shown as lines, and inputs and outputs are denoted by connector symbols.
By Lydie Honorine. Circuit. Published at Thursday, January 04th 2018, 12:58:36 PM. Voltage and current sources can be independent or dependent. Their respective circuit symbols. Independent sources are usually shown as a circle while dependent sources are usually shown as a diamond-shape. Independent sources can have a DC output or a functional output; some examples are a sine wave, square wave, impulse, and linear ramp. Dependent sources can be used to implement a voltage or current which is a function of some other voltage or current in the circuit. Dependent sources are often used to model active circuits that are used for signal amplification.
By Sasha Sara. Diagram. Published at Thursday, January 04th 2018, 11:09:44 AM. A PCB Layout is the resulting design from taking a schematic with specific components and determining how they will physically be laid out on a printed circuit board. To produce a PCB Layout, you must know the connections of components, component sizes (footprints), and a myriad of other properties (such as current, frequencies, emissions, reflections, high voltage gaps, safety considerations, manufacturing tolerances, etc.).
By Valentine Sybille. Circuit. Published at Thursday, January 04th 2018, 07:29:50 AM. A single-layer or single-sided PCB is one that is made out of a single layer of base material or substrate. One side of the base material is coated with a thin layer of metal. Copper is the most common coating due to how well it functions as an electrical conductor. Once the copper base plating is applied, a protective solder mask is usually applied, followed by the last silk-screen to mark out all of the elements on the board.
By Madeleine Catherine. Motor. Published at Wednesday, January 03rd 2018, 17:42:31 PM. The effect of uncompensated mid-band resonance. Though it is possible to accelerate through the resonant region, it is not possible to operate the motor continuously in the speed band without mid-band resonance compensation. This is because the oscillation that causes the motor to stall takes from half a second to 10 seconds to build to amplitude sufficient to stall the motor.
By Lydie Honorine. Circuit. Published at Wednesday, January 03rd 2018, 11:55:52 AM. Impedance essentially can be viewed as frequency-dependent resistance. While resistance of a circuit is the instantaneous ratio between voltage and current, impedance of a circuit is the ratio between voltage and current for steady-state sinusoidal signals, which can vary with of frequency. As the later parts of this section will show, the voltage and current caused by applying a steady-state sinusoidal signal to any combination of resistors, capacitors, and inductors, are related by a constant factor and a phase shift. Therefore, impedance can be expressed by a complex constant using an extended version Ohm’s law.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.