By Madeleine Catherine. Diagram. Publised at Wednesday, July 05th 2017, 04:09:04 AM. The slide switches are also known as “single throw-double pole” (STDP) switches, because only one switch (or throw) exists, but two positions (or poles) are available (a pole is an electrical contact to which the switch can make contact). These switches can be set to output either Vdd (when the actuator is closest to the board’s edge) or GND. The push button switches are also known as “momentary” contact buttons, because they only make contact while they are actively being pressed – they output a GND at rest, and a Vdd only when they are being pressed. The figure below shows typically pushbutton and slide switch circuits used on Digilent boards.
By Lydie Honorine. Circuit. Publised at Friday, December 22nd 2017, 23:34:06 PM. An intuitive way to understand the behavior of voltage and current in electronic circuits is to use hydrodynamic systems as an analogue. In this system, voltage is represented by gravitational potential or height of the fluid column, and current is represented by the fluid flow rate.
By Sasha Sara. Circuit. Published at Saturday, December 16th 2017, 23:35:56 PM. Since single-layer/single-sided PCBs only have their various circuits and electrical components soldered onto one side, they are easy to design and manufacture. This popularity means that they can be purchased at a low-cost, especially for high-volume orders. The low-cost, high volume model means they are commonly used for a variety of applications, including calculators, cameras, radio and stereo equipment, solid state drives, printers and power supplies.
By Sasha Sara. Circuit. Published at Saturday, December 16th 2017, 23:20:56 PM. The circuits and components of a double-layer PCB board are usually connected in one of two ways: either utilizing a through-hole or with the use of a surface-mount. A through-hole connection means that small wires, known as leads, are fed through the holes, with each end of the leads then soldered to the right component.
By Alix Loane. Circuit. Published at Saturday, December 16th 2017, 19:28:35 PM. Most electronic circuits can be represented as a system with an input and an output. The input signal is typically a voltage that is generated by a sensor or by another circuit. The output signal is also
By Cyrielle Marjolaine. Diagram. Published at Saturday, December 16th 2017, 16:52:58 PM. Truly expansive schematics should be split into functional blocks. There might be a section for power input and voltage regulation, or a microcontroller section, or a section devoted to connectors. Try recognizing which sections are which, and following the flow of circuit from input to output. Really good schematic designers might even lay the circuit out like a book, inputs on the left side, outputs on the right.
By Cyrielle Marjolaine. Circuit. Published at Saturday, December 16th 2017, 16:15:18 PM. If the components of the circuit are connected in one single path is it termed as series. The same current would flow through all the components while the voltage would differ from one component to another. For example you have lit three lamps in series to the same power source, the first one would receive more voltage than the last.
By Lydie Honorine. Power. Published at Saturday, December 16th 2017, 16:09:24 PM. It is possible for RO to be negative – an undesirable characteristic often caused by poor layout design in the regulator wiring resulting in inadvertent positive feedback. With negative output resistance the output voltage increases with the load current.
By Madeleine Catherine. Circuit. Published at Saturday, December 16th 2017, 14:21:35 PM. An intuitive way to understand the behavior of voltage and current in electronic circuits is to use hydrodynamic systems as an analogue. In this system, voltage is represented by gravitational potential or height of the fluid column, and current is represented by the fluid flow rate.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.