By Madeleine Catherine. Diagram. Publised at Wednesday, July 05th 2017, 04:09:04 AM. Starting to make sense? These are the basics and may even seem obvious or intuitive to you, such as the wires and if they are connected. Whenever you determine your specific field of electrical engineering, you may see more complex diagrams and symbols. You’ll learn also that different countries use different symbols. For example, of the two symbols for resistors above, the first one is used in the U.S., while the second is used in Europe. You will also learn about the various symbols used for switches, other power supplies, inductors, meters, lamps, LEDs, transistors, antennas, and much more.
By Lydie Honorine. Circuit. Publised at Friday, December 22nd 2017, 23:34:06 PM. An electric current is defined as free flow of electrons and the motivating force behind that free flow of electrons is called Voltage. Voltage is the measurement of potential energy that would move the electrons between two points. Voltage is the push that the electrons require to move within a circuit. Voltage is measured by Volt and Current is measured by Ampere.
By Sasha Sara. Car Wiring. Published at Thursday, December 28th 2017, 00:39:16 AM. Plan out your wiring. Choose the path the wires will follow. Choose the locations of all of your switches, gauges, ignition box, battery, and charging posts. If your past layout was deficient, now is the time to rethink the entire plan.
By Lydie Honorine. Car Wiring. Published at Wednesday, December 27th 2017, 23:39:45 PM. You have a lot of time in the off-season and for your team, designate a qualified person to be in charge of the wiring and the process of rewiring the car as well as being the pointman for mid-season troubleshooting of electrical problems. Don’t assume everything will be OK for next season with what you have, take the effort to make sure. It’s so much fun when things don’t go wrong.
By Lydie Honorine. Power. Published at Wednesday, December 27th 2017, 20:45:16 PM. A variation of the Standard regulator is the quasi-LDO, which uses an NPN and PNP transistor as the pass device. The dropout voltage for a quasi-LDO delivering rated current is usually specified at about 1.5V(max). The actual dropout voltage is temperature and load current dependent, but could never be expected to go lower than about 0.9V (25°C) at even the lightest load. The dropout voltage for the quasi-LDO is higher than the LDO, but lower than the Standard regulator.
By Valentine Sybille. Circuit. Published at Wednesday, December 27th 2017, 18:06:37 PM. The circuits and components of a double-layer PCB board are usually connected in one of two ways: either utilizing a through-hole or with the use of a surface-mount. A through-hole connection means that small wires, known as leads, are fed through the holes, with each end of the leads then soldered to the right component.
By Bertille Solange. Circuit. Published at Wednesday, December 27th 2017, 15:24:49 PM. Many different types of components and devices can be found in modern circuits, including resistors, capacitors, and inductors, semiconductor devices like diodes, transistors, and integrated circuits, transducers like microphones, light sensors and motions sensors, actuators like motors and solenoids, and various other devices like heating and lighting elements. Devices in a circuit are connected to one another by means of electrical conductors, or wires. These wires can move electric currents between various points in a circuit. Once a wire connects two or more devices, the wire and all attached device connectors are said to form a single circuit node or net. Any electrical activity on a given net is communicated to all devices attached to the net. Certain nets provide electric power to devices, and other nets carry information between devices. Nets that carry information are called signals, and signals transport information encoded as voltage levels around a circuit. Signal nets typically use smaller conductors, and transport very small currents. Nets that carry power are called supply rails (or just supplies) and supply rails transport electric power around a circuit. Power nets typically use much larger conductors that signal nets, because they must transport larger currents.
By Lydie Honorine. Circuit. Published at Wednesday, December 27th 2017, 15:23:54 PM. A collection of electronic components that have been assembled and interconnected to perform a given function is commonly referred to as a circuit. The word circuit derives from the fact that electric power must flow from the positive terminal of a power source through one or more electronic devices and back to the negative terminal of a power source, thereby forming a circuit. If the connections between an electronic device and either the positive or negative terminals of a power supply are interrupted, the circuit will be broken and the device will not function.
By Bertille Solange. Motor. Published at Wednesday, December 27th 2017, 15:16:29 PM. The voltage of your power supply is entirely dependent on the inductance rating of your motor, which we learned is translatable to the number of turns of wire in the stator. Every motor model will have a different inductance rating and will therefore have a different maximum voltage. To figure out what the maximum power supply voltage should be, use the following formula with the motor’s inductance in millihenries (mH) used for the L value.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.