By Valentine Sybille. Diagram. Publised at Monday, November 20th 2017, 08:03:03 AM. Knowing how to read circuits is a very useful skill that will help you out all the time. especially if you start messing around with building little electronics projects.
By Alix Loane. Circuit. Published at Tuesday, December 26th 2017, 09:18:43 AM. Electric current is the rate at which electric charge flows through a given area. Current is measured in the unit of Coulombs per second, which is known as an ampere (A). In an electronic circuit, the electromagnetic problem of currents is typically simplified as a current flowing through particular circuit components.
By Valentine Sybille. Motor. Published at Tuesday, December 26th 2017, 09:08:58 AM. Ideally, you will be connecting motors per an installation drawing. In that case, it’s a matter of correctly identifying the motor leads by number and connecting them per the drawing. Don’t try to “wing it” when replacing a motor, working with OEM equipment, or installing a motor when such drawings have been provided. But there’s a catch. We’ll get to that in a moment.
By Bertille Solange. Circuit. Published at Tuesday, December 26th 2017, 09:04:42 AM. If the components of the circuit are connected in one single path is it termed as series. The same current would flow through all the components while the voltage would differ from one component to another. For example you have lit three lamps in series to the same power source, the first one would receive more voltage than the last.
By Bertille Solange. Circuit. Published at Tuesday, December 26th 2017, 07:58:11 AM. Electric circuits use electric power to perform some function, like energize a heating or lighting element, turn a motor, or create an electromagnetic filed. Electronic circuits differ from electric circuits in that they use devices that can themselves be controlled by other electric signals. Restated, electronic circuits are built from devices that use electricity to control electricity. Most electronic circuits use signals that are within 5 to 10 volts of ground; most circuits built within the past several years use signals that are within 3 to 5 volts from ground. Some electronic circuits represent information encoded as continuous voltage levels that can wander between the high and low voltage supply rails – these are called analog circuits. As an example, a sound pressure level transducer (i.e. a microphone) might drive a signal between 0V and 3.3V in direct proportion to the detected sound pressure level. In this case, the voltage signal output from the microphone is said to be an analog ifthe sound pressure wave itself. Other circuits use only two distinct voltage levels to represent information. Most often, these two voltage levels use the same voltages supplied by the power rails. In these circuits, called digital circuits, all information must be represented as binary numbers, with a signal at 0V (or ground) representing one kind of information, and a signal at 3.3V (or whatever the upper voltage supply rail provides) representing the other kind of information. In this series of modules, we will confine our discussions to digital circuits.
By Charlotte Myriam. Amplifier. Published at Tuesday, December 26th 2017, 07:53:55 AM. At this point things can get a bit problematic. Where should the connections be made and how to connect them. I have found that the best place for a central ground to be at the signal input ground. This will be where the connections to other external equipment is made. In a typical audio component there will be left and right channel inputs. Each channel will be via a shielded cable from the source (CD, FM, etc.). At the input jacks I have found that you can connect the two input signal ground returns together (not to the chassis) using isolated jacks provided you do not run shielded cable with both ends connected together internally to the unit. This part is often hard to envision, but you do not want multiple ground paths for the signal. This is likely to cause a ground loop, more about that later. A common error is to connect the signal grounds together at the input jacks and then run shielded cable inside the unit to something like a volume control and connect the shields together there. The shields then acts as conductors and not solely as shields. Use only one end of the shield inside equipment. If needed, run a separate ground wire to the volume control or where ever the signal is going. It will be the ground reference for the signal and the shields will be only shields. This can greatly improve the signal to noise in a piece of equipment.
By Cyrielle Marjolaine. Diagram. Published at Tuesday, December 26th 2017, 07:36:43 AM. In addition to reading this instructable it may be a good idea for you to read my other instructable "electronics components and what they do" to get a good understanding of what you are doing when building a project.
By Charlotte Myriam. Motor. Published at Tuesday, December 26th 2017, 07:36:40 AM. Typically, the motor will be a 6-lead or 9-lead motor. Motors with six leads are nearly always single-voltage motors. Such motors might be dual-winding motors, in which case you can wire them for a part winding start. You can connect them for a delta start or a wye start.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.