By Lydie Honorine. Circuit. Publised at Friday, December 22nd 2017, 23:34:06 PM. Resistors, capacitors, and inductors are the fundamental components of electronic circuits. In fact, all electronic circuits can be equivalently represented by circuits of these three components together with voltage and current sources.
By Madeleine Catherine. Diagram. Publised at Wednesday, July 05th 2017, 04:09:04 AM. Several different resistors are used on Digilent boards. Some are used to limit LED current, and some are used on inputs (like the button and switch circuits) to both limit the currents flowing to the main chip, and to help protect against electrostatic discharge (or ESD – more on this topic later). The resistors on the Digilent boards, like most resistors used in digital systems, are physically small because they will not encounter large voltages or currents. For these smaller resistors, the resistor value in Ohms is printed in microscopic numbers on the resistor body, not visible to the naked eye.
By Charlotte Myriam. Motor. Published at Tuesday, December 26th 2017, 07:36:40 AM. To make your own power supply you must have three key components: a transformer, bridge rectifier, and filter capacitor. The transformer’s current rating must be sufficient to adequately run all motors that will be run from it using the above current formula. The DC output voltage will be 1.4 times the transformer’s AC voltage rating of the secondary. For example, a 24VAC transformer secondary will provide about 34VDC at the output of the supply. The bridge rectifier’s voltage and current ratings must exceed what the supply will deliver. Finally the minimum filter capacitor size must be calculated.
By Valentine Sybille. Diagram. Published at Tuesday, December 26th 2017, 07:35:16 AM. Voltage nodes are single-terminal schematic components, which we can connect component terminals to in order to assign them to a specific voltage level. These are a special application of net names, meaning all terminals connected to a like-named voltage node are connected together.
By Lydie Honorine. Diagram. Published at Tuesday, December 26th 2017, 07:31:48 AM. In contrast to digital circuits, analog circuits use signals whose voltage levels are not constrained to two distinct levels, but instead can assume any value between Vdd and GND. Many input devices, particularly those using electronic sensors (e.g., microphones, cameras, thermometers, pressure sensors, motion and proximity detectors, etc.) produce analog voltages at their outputs. In modern electronic devices, it is likely that such signals will be converted to digital signals before they are used within the device. For example, a digital voice-memo recording device uses an analog microphone circuit to convert sound pressure waves into voltage waves on an internal circuit node. A special circuit called an analog-to-digital converter, or ADC, converts that analog voltage to a binary number that can be represented as a bus in a digital circuit. An ADC functions by taking samples of the input analog signal, measuring the magnitude of the input voltage signal (usually with reference to GND), and assigning a binary number to the measured magnitude. Once an analog signal has been converted to a binary number, a bus can carry that digital information around a circuit. In a similar manner, digital signals can be reconstituted into analog signals using a digital-to-analog converter. Thus, a binary number that represents a sample of an audio waveform can be converted to an analog signal that can, for example, drive a speaker.
By Madeleine Catherine. Circuit. Published at Tuesday, December 26th 2017, 07:11:55 AM. Double-layer or double-sided PCBs have a base material with a thin layer of conductive metal, like copper, applied to both sides of the board. Holes drilled through the board allow circuits on one side of the board to connect to circuits on the other.
By Cyrielle Marjolaine. Power. Published at Tuesday, December 26th 2017, 06:48:57 AM. There are many new regulators which have tighter output tolerances (better than 2% is common), achieved through the use of a laser-trim process. Also, many of the new regulators have separate output specifications that cover room temperature/full operating temperature range, and full-load/light-load conditions.
By Jessica Mireille. Diagram. Published at Tuesday, December 26th 2017, 06:21:40 AM. Inductors are usually represented by either a series of curved bumps, or loopy coils. International symbols may just define an inductor as a filled-in rectangle.
By Madeleine Catherine. Diagram. Published at Tuesday, December 26th 2017, 06:12:51 AM. A first look at a circuit diagram may be confusing, but if you can read a subway map, you can read schematics. The purpose is the same: getting from point A to point B. Literally, a circuit is the path that allows electricity to flow. If you know what to look for, it’ll become second nature. While at first you’ll just be reading them, eventually you will start creating your own. This guide will show you a few of the common symbols that you are sure to see in your future electrical engineering career.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.