By Lydie Honorine. Diagram. Publised at Monday, December 18th 2017, 05:16:38 AM. Several different resistors are used on Digilent boards. Some are used to limit LED current, and some are used on inputs (like the button and switch circuits) to both limit the currents flowing to the main chip, and to help protect against electrostatic discharge (or ESD – more on this topic later). The resistors on the Digilent boards, like most resistors used in digital systems, are physically small because they will not encounter large voltages or currents. For these smaller resistors, the resistor value in Ohms is printed in microscopic numbers on the resistor body, not visible to the naked eye.
By Charlotte Myriam. Diagram. Published at Friday, November 17th 2017, 02:53:47 AM. In a PCB that uses through-hole technology, holes are drilled through the pads so that component leads can be inserted and then fastened (soldered) in place. In a PCB that uses surface-mount technology, component leads are soldered directly to the pads on the surface. Each set of pads (or holes) in the PCB is intended to receive a particular component. To identify which component must be loaded where, reference designators are printed on the circuit board immediately adjacent to the pads using a silk-screen process. A parts list links a designated set of pads to a physical component by describing the component and assigning it a particular reference designator. The reference designators guide assemblers and testers when they are working with the PCB. Many components must be placed into the PCB in a particular orientation. By convention, components that require a particular orientation have one lead designated as pin 1. On the PCB, a square pad or silkscreen indicator typically denotes pin 1.
By Madeleine Catherine. Circuit. Published at Thursday, November 16th 2017, 01:05:36 AM. An inductor is a device that stores energy in the form of current. The most common form of inductors is a wire wound into a coil. The magnetic field generated by the wire creates a counter-acting electric field which impedes changes to the current.
By Cyrielle Marjolaine. Diagram. Published at Tuesday, November 14th 2017, 23:06:49 PM. Voltage nodes are single-terminal schematic components, which we can connect component terminals to in order to assign them to a specific voltage level. These are a special application of net names, meaning all terminals connected to a like-named voltage node are connected together.
By Madeleine Catherine. Diagram. Published at Sunday, November 12th 2017, 22:58:49 PM. Circuits often require output devices to communicate their state to an user. Examples of electronic output devices include computer monitors, LCD alphanumeric panels (as on a calculator), small lamps or light-emitting diodes (LED), etc. Digilent boards include different output devices, but all of them include some number of individual LED, and seven-segment LED displays that can display the digits 0-9 in each digit position (each segment in the seven-segment display contains a single LED). LED are two-terminal semiconductor devices that conduct current in only one direction (from the anode to the cathode). The small LED chips are secured inside a plastic housing, and they emit light at a givenfrequency (RED, YELLOW, etc.) when a small electric current (typically 10mA to 25mA) flows through them.
By Lydie Honorine. Circuit. Published at Saturday, November 11th 2017, 22:49:05 PM. In some circuits, there are virtual grounds, which are nodes at the same voltage as ground, but are not connected to a power supply. When current flows into the virtual ground, the voltage at the virtual ground may change relative to the real ground, and the consequences of this situation must be analyzed carefully.
By Valentine Sybille. Diagram. Published at Thursday, November 09th 2017, 22:24:37 PM. In a digital circuit, power supply voltage levels are constrained to two distinct values – “logic high voltage” (called LHV or Vdd) and “logic low voltage” (called LLV or GND). The GND node in any circuit is the universal reference voltage against which all other voltages are measured (in modern digital circuits, GND is typically the lowest voltage in the circuit). In a schematic, it is often difficult to show lines connecting all GND nodes; rather, any nodes labeled GND are assumed to be connected into the same node. Often, a downward pointing triangle symbol, is attached to a GND node in addition to (or instead of) the GND label. The Vdd node in a digital circuit is typically the highest voltage, and all nodes labeled Vdd are tied together into the same node. Vdd may be thought of as the “source” of positive charges in a circuit, and GND may be thought of as the “source” of negative charges in a circuit. In modern digital systems, Vdd and GND are separated by anywhere from 1 to 5 volts. Older or inexpensive circuits typically use 5 volts, while newer circuits use 1-3 volts.
By Charlotte Myriam. Diagram. Published at Wednesday, November 08th 2017, 21:37:58 PM. Inductors are usually represented by either a series of curved bumps, or loopy coils. International symbols may just define an inductor as a filled-in rectangle.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.