By Bertille Solange. Circuit. Publised at Tuesday, August 15th 2017, 22:28:56 PM. Impedance essentially can be viewed as frequency-dependent resistance. While resistance of a circuit is the instantaneous ratio between voltage and current, impedance of a circuit is the ratio between voltage and current for steady-state sinusoidal signals, which can vary with of frequency. As the later parts of this section will show, the voltage and current caused by applying a steady-state sinusoidal signal to any combination of resistors, capacitors, and inductors, are related by a constant factor and a phase shift. Therefore, impedance can be expressed by a complex constant using an extended version Ohm’s law.
By Bertille Solange. Circuit. Published at Saturday, August 26th 2017, 05:44:44 AM. First let’s understand the difference between these two terms. While electrical is the basis of everything, electronic is a subset of electrical. An electrical circuit deals with just the flow of electrons and has components like resistors, inductors and capacitors and uses Alternating Current Source; while electronic circuit deals with the transformation of current and controlling the motion of the electrons and uses Direct Current Source. An electrical circuit is termed as Passive because it doesn’t have any such component that reacts to the current/voltage that passes through them and electronic circuit is called active because of the additional components like diode or a transformer that react to the current/voltage that passes through.
By Alix Loane. Diagram. Published at Friday, August 25th 2017, 04:49:43 AM. A block diagram shows a higher level (or organizational layout) of functional units in a circuit (or a device, machine, or collection of these). It is meant to show data flow or organization between separate units of function. A block diagram gives you an overview of the interconnected nature of circuit assemblies or components.
By Alix Loane. Diagram. Published at Monday, August 21st 2017, 02:43:00 AM. A first look at a circuit diagram may be confusing, but if you can read a subway map, you can read schematics. The purpose is the same: getting from point A to point B. Literally, a circuit is the path that allows electricity to flow. If you know what to look for, it’ll become second nature. While at first you’ll just be reading them, eventually you will start creating your own. This guide will show you a few of the common symbols that you are sure to see in your future electrical engineering career.
By Valentine Sybille. Diagram. Published at Saturday, August 19th 2017, 00:16:17 AM. In a PCB that uses through-hole technology, holes are drilled through the pads so that component leads can be inserted and then fastened (soldered) in place. In a PCB that uses surface-mount technology, component leads are soldered directly to the pads on the surface. Each set of pads (or holes) in the PCB is intended to receive a particular component. To identify which component must be loaded where, reference designators are printed on the circuit board immediately adjacent to the pads using a silk-screen process. A parts list links a designated set of pads to a physical component by describing the component and assigning it a particular reference designator. The reference designators guide assemblers and testers when they are working with the PCB. Many components must be placed into the PCB in a particular orientation. By convention, components that require a particular orientation have one lead designated as pin 1. On the PCB, a square pad or silkscreen indicator typically denotes pin 1.
By Charlotte Myriam. Circuit. Published at Thursday, August 17th 2017, 22:51:19 PM. When multiple components are connected in parallel, the voltage drop is the same across all components. When multiple components are connected in series, the total voltage is the sum of the voltages across each component. These two statements can be generalized as Kirchoff’s Voltage Law (KVL), which states that the sum of voltages around any closed loop (e.g. starting at one node, and ending at the same node) is zero.
By Bertille Solange. Circuit. Published at Tuesday, August 15th 2017, 22:28:56 PM. Ohm’s law states that the current through a conductor between two points is directly proportional to the potential difference across those two points. It means that more the resistance lesser current would flow. I=V/R This would apply to any component of a circuit. For example conductors would increase the current flow and the inductors would decrease it.
By Cyrielle Marjolaine. Circuit. Published at Monday, August 14th 2017, 20:40:30 PM. In some circuits, there are virtual grounds, which are nodes at the same voltage as ground, but are not connected to a power supply. When current flows into the virtual ground, the voltage at the virtual ground may change relative to the real ground, and the consequences of this situation must be analyzed carefully.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.