By Charlotte Myriam. Circuit. Publised at Tuesday, December 19th 2017, 15:29:49 PM. Many different types of components and devices can be found in modern circuits, including resistors, capacitors, and inductors, semiconductor devices like diodes, transistors, and integrated circuits, transducers like microphones, light sensors and motions sensors, actuators like motors and solenoids, and various other devices like heating and lighting elements. Devices in a circuit are connected to one another by means of electrical conductors, or wires. These wires can move electric currents between various points in a circuit. Once a wire connects two or more devices, the wire and all attached device connectors are said to form a single circuit node or net. Any electrical activity on a given net is communicated to all devices attached to the net. Certain nets provide electric power to devices, and other nets carry information between devices. Nets that carry information are called signals, and signals transport information encoded as voltage levels around a circuit. Signal nets typically use smaller conductors, and transport very small currents. Nets that carry power are called supply rails (or just supplies) and supply rails transport electric power around a circuit. Power nets typically use much larger conductors that signal nets, because they must transport larger currents.
By Alix Loane. Car Wiring. Published at Saturday, December 30th 2017, 04:37:00 AM. Now that you have a good idea of how you want to wire your car, the routes, the connections, and the switches and gauges, think about duplicating the wiring just in case you need it.
By Charlotte Myriam. Diagram. Published at Saturday, December 30th 2017, 04:11:48 AM. A PCB Layout is the resulting design from taking a schematic with specific components and determining how they will physically be laid out on a printed circuit board. To produce a PCB Layout, you must know the connections of components, component sizes (footprints), and a myriad of other properties (such as current, frequencies, emissions, reflections, high voltage gaps, safety considerations, manufacturing tolerances, etc.).
By Lydie Honorine. Car Wiring. Published at Saturday, December 30th 2017, 01:33:56 AM. The most common type of fuse is a short length of thin wire enclosed in a heatproof casing often glass. The size of the fuse wire is the thinnest that can carry the normal current of the circuit without overheating, and it is rated in amps.
By Alix Loane. Motor. Published at Saturday, December 30th 2017, 00:13:39 AM. When using multiple drives from a common power supply, use individual supply and ground wires to each drive and return them to a common point back at the power supply. This is called a “star” power supply distribution; never use a “daisy-chain” power distribution, where the supply and ground wires for the next drives are picked up from the previous one.
By Alix Loane. Motor. Published at Friday, December 29th 2017, 20:40:03 PM. If one changes the power supply voltage, then a new family of speed-torque curves result. As an example, if the power supply voltage is doubled then a new curve is generated; the curve now has twice the torque at any given speed in region 2. Since power equals torque times speed, the motor now generates twice as much power as well.
By Madeleine Catherine. Car Wiring. Published at Friday, December 29th 2017, 19:35:53 PM. When fitting extra accessories, such as a rear window heater which consumes a heavy current, always wire it through the ignition switch. Some ancillary components can be operated without the ignition turned on by turning the switch to the "auxiliary" position. A radio is usually wired through this switch, so that it can be played with the engine off.
By Lydie Honorine. Motor. Published at Friday, December 29th 2017, 17:00:56 PM. There is a special consideration if the power supply will be at or near the maximum voltage rating of the drive. If the motor will be rapidly decelerating a large inertial load from a high speed, care has to be taken to absorb the returned energy. The energy stored in the momentum of the load must be removed during deceleration and be safely dissipated. Because of its efficiency, the drive has no means of dissipating this energy so it returns it to the power supply. In effect, instead of drawing current from the power supply, the drive becomes a source of current itself. This current may charge the power supply capacitor to destructive voltage levels.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.