By Charlotte Myriam. Diagram. Publised at Monday, November 20th 2017, 14:55:41 PM. In a PCB that uses through-hole technology, holes are drilled through the pads so that component leads can be inserted and then fastened (soldered) in place. In a PCB that uses surface-mount technology, component leads are soldered directly to the pads on the surface. Each set of pads (or holes) in the PCB is intended to receive a particular component. To identify which component must be loaded where, reference designators are printed on the circuit board immediately adjacent to the pads using a silk-screen process. A parts list links a designated set of pads to a physical component by describing the component and assigning it a particular reference designator. The reference designators guide assemblers and testers when they are working with the PCB. Many components must be placed into the PCB in a particular orientation. By convention, components that require a particular orientation have one lead designated as pin 1. On the PCB, a square pad or silkscreen indicator typically denotes pin 1.
By Bertille Solange. Diagram. Published at Wednesday, December 27th 2017, 02:16:25 AM. The unloaded PCB appears green because thin sheets of green plastic have been applied to both sides (otherwise the PCB would appear pale yellow). Called solder masks, these sheets cover all exposed metal other than the component pads and holes so that errant solder can not inadvertently short (or electrically connect) the printed wires. All metal surfaces other than the exposed pads and holes (i.e., the wires) are underneath the solder mask. Not infrequently, blue or even red solder masks are used.
By Sasha Sara. Circuit. Published at Wednesday, December 27th 2017, 02:05:06 AM. Electric circuits use electric power to perform some function, like energize a heating or lighting element, turn a motor, or create an electromagnetic filed. Electronic circuits differ from electric circuits in that they use devices that can themselves be controlled by other electric signals. Restated, electronic circuits are built from devices that use electricity to control electricity. Most electronic circuits use signals that are within 5 to 10 volts of ground; most circuits built within the past several years use signals that are within 3 to 5 volts from ground. Some electronic circuits represent information encoded as continuous voltage levels that can wander between the high and low voltage supply rails – these are called analog circuits. As an example, a sound pressure level transducer (i.e. a microphone) might drive a signal between 0V and 3.3V in direct proportion to the detected sound pressure level. In this case, the voltage signal output from the microphone is said to be an analog ifthe sound pressure wave itself. Other circuits use only two distinct voltage levels to represent information. Most often, these two voltage levels use the same voltages supplied by the power rails. In these circuits, called digital circuits, all information must be represented as binary numbers, with a signal at 0V (or ground) representing one kind of information, and a signal at 3.3V (or whatever the upper voltage supply rail provides) representing the other kind of information. In this series of modules, we will confine our discussions to digital circuits.
By Charlotte Myriam. Diagram. Published at Wednesday, December 27th 2017, 00:59:04 AM. The voltage source, such as a battery, is needed in order to cause the current to flow through the circuit. In addition, there needs to be a conductive path that provides a route for the electricity to flow. Finally, a proper circuit needs a load that consumes the power.
By Alix Loane. Circuit. Published at Wednesday, December 27th 2017, 00:57:22 AM. The concept of complex impedance introduces a unified representation for resistors, capacitors, and inductors, whereby a circuit’s frequency response from input to output can be determined using KVL and KCL, where each element is assigned the appropriate impedance. The key assumption to this point is that the input to the circuit must consist solely of DC and/or sinusoidal signals. Now, this analysis is be extended to include arbitrary input signals by using the mathematical techniques of Laplace transforms.
By Bertille Solange. Circuit. Published at Wednesday, December 27th 2017, 00:32:02 AM. If the components of the circuit are connected in one single path is it termed as series. The same current would flow through all the components while the voltage would differ from one component to another. For example you have lit three lamps in series to the same power source, the first one would receive more voltage than the last.
By Bertille Solange. Diagram. Published at Wednesday, December 27th 2017, 00:30:05 AM. A schematic shows connections in a circuit in a way that is clear and standardized. It is a way of communicating to other engineers exactly what components are involved in a circuit as well as how they are connected. A good schematic will show component names and values, and provide labels for sections or components to help communicate the intended purpose. Note how connections on wires (or "nets") are shown using dots and non-connections are shown without a dot.
By Jessica Mireille. Power. Published at Tuesday, December 26th 2017, 23:57:09 PM. The function of current limiting circuitry is to prevent damage to the IC when an overload is placed on the output of the regulator (the load impedance is too low). Without current limiting, the regulator would source excessive load current and destroy the pass transistor inside the part.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.