By Cyrielle Marjolaine. Power. Publised at Monday, December 18th 2017, 10:47:11 AM. In thermal limiting, the output voltage drops and the load current can be reduced to any value (including zero). No performance characteristic specifications apply when a part is operating in thermal shutdown mode.
By Cyrielle Marjolaine. Diagram. Published at Monday, December 18th 2017, 13:32:30 PM. Production circuit boards typically start out as thin sheets of fiberglass (about 1mm thick) that are completely covered on both sides with very thin sheets of metal (typically copper). A "standard" circuit board might use a 1 ounce copper process, which means that one ounce of copper is evenly spread across 1 square foot of circuit board. During the manufacturing process, wire patterns are "printed" onto the copper surfaces using a compound that resists etching (hence the name Printed Circuit Board or PCB). The boards are subjected to a chemical etching process that removes all exposed copper. The remaining, un-etched copperforms wires that will interconnect the circuit board components, and small pads that define the regions where component leads will be attached.
By Bertille Solange. Power. Published at Monday, December 18th 2017, 13:09:45 PM. Linear IC regulators contain built-in protection circuits which make them virtually immune to damage from either excessive load current or high operating temperature.
By Charlotte Myriam. Diagram. Published at Monday, December 18th 2017, 12:40:04 PM. Now’s the fun stuff. Completing an electrical engineering degree and then getting a job in the field means you will see a lot a lot a lot of these schematics. It’s important to understand exactly what is going on with these. While they can (and will) get very complex, these are just a few of the common graphics to get your footing on.
By Jessica Mireille. Amplifier. Published at Monday, December 18th 2017, 11:38:21 AM. So at this point we have the signal and power grounds connected. Next is the chassis. There are a number of ways that we can accomplish this connection. The key thought is to maintain the shock protection while using it as an EMI shield. Sometimes it can connect directly to the ground at the input jacks. This was a fairly common practice in the earlier days of electronic equipment. These were also in many cases what I would consider lower fidelity equipment and things that did not benefit from three wire AC mains. I do not recommend this as there is the possibility of introducing the EMI noise from the chassis and AC mains earth ground into the signal path. Most methods of making the connection involve resistors, capacitors or rectifiers. I suspect all will work. My preference is for a parallel combination of a metal film resistor of about 120 ohms (1/2 Watt is fine) and a type X2 capacitor in the range of 0.1 to 0.22uF. Type X2 capacitors are rated for use with AC mains circuits. I have seen ceramics and polys used there but since they are not usually AC mains rated I strongly recommend against them. The capacitor and resistor provide sufficient isolation between the chassis and circuitry to allow the chassis to be an effective EMI shield but not induce the EMI into the active circuitry.
By Lydie Honorine. Diagram. Published at Monday, December 18th 2017, 11:22:07 AM. In contrast to digital circuits, analog circuits use signals whose voltage levels are not constrained to two distinct levels, but instead can assume any value between Vdd and GND. Many input devices, particularly those using electronic sensors (e.g., microphones, cameras, thermometers, pressure sensors, motion and proximity detectors, etc.) produce analog voltages at their outputs. In modern electronic devices, it is likely that such signals will be converted to digital signals before they are used within the device. For example, a digital voice-memo recording device uses an analog microphone circuit to convert sound pressure waves into voltage waves on an internal circuit node. A special circuit called an analog-to-digital converter, or ADC, converts that analog voltage to a binary number that can be represented as a bus in a digital circuit. An ADC functions by taking samples of the input analog signal, measuring the magnitude of the input voltage signal (usually with reference to GND), and assigning a binary number to the measured magnitude. Once an analog signal has been converted to a binary number, a bus can carry that digital information around a circuit. In a similar manner, digital signals can be reconstituted into analog signals using a digital-to-analog converter. Thus, a binary number that represents a sample of an audio waveform can be converted to an analog signal that can, for example, drive a speaker.
By Cyrielle Marjolaine. Power. Published at Monday, December 18th 2017, 10:47:11 AM. The thermal limit circuit can sink all of the current from the error amplifier output, and keep the regulator output voltage/current as low as needed to maintain the junction temperature at 160°C. As shown, the thermal limiter can "override" the voltage control loop when needed to prevent damage to the IC.
By Bertille Solange. Diagram. Published at Monday, December 18th 2017, 09:48:57 AM. A PCB Layout is the resulting design from taking a schematic with specific components and determining how they will physically be laid out on a printed circuit board. To produce a PCB Layout, you must know the connections of components, component sizes (footprints), and a myriad of other properties (such as current, frequencies, emissions, reflections, high voltage gaps, safety considerations, manufacturing tolerances, etc.).
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.