By Cyrielle Marjolaine. Diagram. Publised at Sunday, November 19th 2017, 23:35:54 PM. Wiring diagrams use standard symbols for wiring devices, usually different from those used on schematic diagrams. The electrical symbols not only show where something is to be installed, but also what type of device is being installed. For example, a surface ceiling light is shown by one symbol, a recessed ceiling light has a different symbol, and a surface fluorescent light has another symbol. Each type of switch has a different symbol and so do the various outlets. There are symbols that show the location of smoke detectors, the doorbell chime, and thermostat. On large projects symbols may be numbered to show, for example, the panel board and circuit to which the device connects, and also to identify which of several types of fixture are to be installed at that location.
By Sasha Sara. Circuit. Published at Saturday, December 23rd 2017, 19:42:57 PM. An often used and sometimes confusing term in electronic circuits is the word ground. The ground is a circuit node to which all voltages in a circuit are referenced. In a constant voltage supply circuit, one terminal from each voltage supply is typically connected to ground, or is grounded. For example, the negative terminal of a positive power supply is usually connected to ground so that any current drawn out of the positive terminal can be put back into the negative terminal via ground.
By Sasha Sara. Diagram. Published at Saturday, December 23rd 2017, 19:23:03 PM. There are two commonly used capacitor symbols. One symbol represents a polarized (usually electrolytic or tantalum) capacitor, and the other is for non-polarized caps. In each case there are two terminals, running perpendicularly into plates. The symbol with one curved plate indicates that the capacitor is polarized. The curved plate represents the cathode of the capacitor, which should be at a lower voltage than the positive, anode pin. A plus sign might also be added to the positive pin of the polarized capacitor symbol.
By Lydie Honorine. Circuit. Published at Saturday, December 23rd 2017, 18:22:12 PM. In the hydrodynamic analogy of electronic circuits, resistors are equivalent to a pipe. As fluid flows through a pipe, frictional drag forces at the walls dissipate energy from the flow and thus reducing the pressure, or equivalently, the potential energy of the fluid in the pipe. A small resistor is equivalent to a large diameter pipe that will allow for a high flow rate, whereas a large resistor is equivalent to a small diameter pipe that greatly constricts the flow rate.
By Alix Loane. Diagram. Published at Saturday, December 23rd 2017, 17:48:37 PM. A PCB Layout is the resulting design from taking a schematic with specific components and determining how they will physically be laid out on a printed circuit board. To produce a PCB Layout, you must know the connections of components, component sizes (footprints), and a myriad of other properties (such as current, frequencies, emissions, reflections, high voltage gaps, safety considerations, manufacturing tolerances, etc.).
By Charlotte Myriam. Diagram. Published at Saturday, December 23rd 2017, 17:27:05 PM. Starting to make sense? These are the basics and may even seem obvious or intuitive to you, such as the wires and if they are connected. Whenever you determine your specific field of electrical engineering, you may see more complex diagrams and symbols. You’ll learn also that different countries use different symbols. For example, of the two symbols for resistors above, the first one is used in the U.S., while the second is used in Europe. You will also learn about the various symbols used for switches, other power supplies, inductors, meters, lamps, LEDs, transistors, antennas, and much more.
By Jessica Mireille. Circuit. Published at Saturday, December 23rd 2017, 16:11:17 PM. Impedance is one of the most important concepts in electronic circuits. The purpose of impedance is to generalize the idea of resistance to create a component. To capture the behavior of resistors, capacitors, and inductors, for steadystate sinusoidal signals. This generalization is motivated by the fact that as long as the circuit is linear, its behavior can be analyzed using KVL and KCL.
By Cyrielle Marjolaine. Power. Published at Saturday, December 23rd 2017, 16:09:08 PM. The output voltage is controlled using a feedback loop, which requires some type of compensation to assure loop stability. Most linear regulators have built-in compensation, and are completely stable without external components. Some regulators (like Low-Dropout types), do require some external capacitance connected from the output lead to ground to assure regulator stability.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.