By Cyrielle Marjolaine. Diagram. Publised at Sunday, November 19th 2017, 23:35:54 PM. A schematic shows connections in a circuit in a way that is clear and standardized. It is a way of communicating to other engineers exactly what components are involved in a circuit as well as how they are connected. A good schematic will show component names and values, and provide labels for sections or components to help communicate the intended purpose. Note how connections on wires (or "nets") are shown using dots and non-connections are shown without a dot.
By Lydie Honorine. Diagram. Published at Monday, January 01st 2018, 13:07:23 PM. There are two commonly used capacitor symbols. One symbol represents a polarized (usually electrolytic or tantalum) capacitor, and the other is for non-polarized caps. In each case there are two terminals, running perpendicularly into plates. The symbol with one curved plate indicates that the capacitor is polarized. The curved plate represents the cathode of the capacitor, which should be at a lower voltage than the positive, anode pin. A plus sign might also be added to the positive pin of the polarized capacitor symbol.
By Bertille Solange. Diagram. Published at Monday, January 01st 2018, 12:43:12 PM. In addition to reading this instructable it may be a good idea for you to read my other instructable "electronics components and what they do" to get a good understanding of what you are doing when building a project.
By Valentine Sybille. Diagram. Published at Monday, January 01st 2018, 11:51:03 AM. Be sure to use this to produce a schematic if you need to ask questions about your circuit. It will help others to quickly understand the circuit diagrams are pictures with symbols that have differed from country to country and have changed over time, but are now to a large extent internationally standardized. Simple components often had symbols intended to represent some feature of the physical construction of the device. For example, the symbol for a resistor shown here dates back to the days when that component was made from a long piece of wire wrapped in such a manner as to not produce inductance, which would have made it a coil. These wirewound resistors are now used only in high-power applications, smaller resistors being cast from carbon composition (a mixture of carbon and filler) or fabricated as an insulating tube or chip coated with a metal film. The internationally standardized symbol for a resistor is therefore now simplified to an oblong, sometimes with the value in ohms written inside, instead of the zig-zag symbol. A less common symbol is simply a series of peaks on one side of the line representing the conductor, rather than back-and-forth as shown here. Components and connections involved in your design.
By Charlotte Myriam. Motor. Published at Monday, January 01st 2018, 09:21:29 AM. To avoid confusion obtain a pocket motor wiring guide and refer to it while performing the work. We mentioned a catch, earlier. With these and other motor wiring variations possible, it’s easy to make a mistake. That drawing we said to follow could be wrong. Before you connect any wires, check the drawing carefully. That’s another reason to have that pocket motor wiring guide.
By Cyrielle Marjolaine. Diagram. Published at Monday, January 01st 2018, 08:30:28 AM. As discussed earlier, a digital circuit represents and manipulates information encoded as electric signals that can assume one of two voltages – logic-high voltage (or Vdd) and logic-low voltage (or GND). A digital circuit requires a power supply that can produce these two voltages, and these same supply voltages are also used to encode information in the form of two-state, or binary signals. Thus,if a given circuit node is at Vdd, then that signal is said to carry a logic ‘1’; if the node is at GND, then the node carries a logic ‘0’. The components in digital circuits are simple on/off switches that can pass logic ‘1’ and logic ‘0’ signals from one circuit node to another. Most typically, these switches are arranged to combine input signals to produce an output signal according to basic logic relationships. For example, one well-known logic circuit is an AND gate that combines two input signals to produce an output that is the logic AND of the inputs (i.e., if both input1 and input2 are a ‘1’, then the output is a ‘1’).
By Charlotte Myriam. Motor. Published at Monday, January 01st 2018, 06:19:04 AM. Before you actually make any bolted connections, verify the correct rotation using a rotation tester. Also make sure you connect the “ground” wire to the “grounding” terminal of the motor. Note that this must be the power supply ground conductor, not a wire leading to a ground rod nearby.
By Madeleine Catherine. Motor. Published at Monday, January 01st 2018, 06:16:35 AM. Typically, the motor will be a 6-lead or 9-lead motor. Motors with six leads are nearly always single-voltage motors. Such motors might be dual-winding motors, in which case you can wire them for a part winding start. You can connect them for a delta start or a wye start.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.