By Cyrielle Marjolaine. Diagram. Publised at Sunday, November 19th 2017, 23:35:54 PM. In contrast to digital circuits, analog circuits use signals whose voltage levels are not constrained to two distinct levels, but instead can assume any value between Vdd and GND. Many input devices, particularly those using electronic sensors (e.g., microphones, cameras, thermometers, pressure sensors, motion and proximity detectors, etc.) produce analog voltages at their outputs. In modern electronic devices, it is likely that such signals will be converted to digital signals before they are used within the device. For example, a digital voice-memo recording device uses an analog microphone circuit to convert sound pressure waves into voltage waves on an internal circuit node. A special circuit called an analog-to-digital converter, or ADC, converts that analog voltage to a binary number that can be represented as a bus in a digital circuit. An ADC functions by taking samples of the input analog signal, measuring the magnitude of the input voltage signal (usually with reference to GND), and assigning a binary number to the measured magnitude. Once an analog signal has been converted to a binary number, a bus can carry that digital information around a circuit. In a similar manner, digital signals can be reconstituted into analog signals using a digital-to-analog converter. Thus, a binary number that represents a sample of an audio waveform can be converted to an analog signal that can, for example, drive a speaker.
By Sasha Sara. Diode. Published at Saturday, December 23rd 2017, 10:43:50 AM. A diode conducts strongly in the direction of the black arrow, and essentially 000 current can flow in the opposite direction. A diode made of silicon has a forward voltage between 0.60−0.75V.
By Sasha Sara. Diagram. Published at Saturday, December 23rd 2017, 10:37:29 AM. A first look at a circuit diagram may be confusing, but if you can read a subway map, you can read schematics. The purpose is the same: getting from point A to point B. Literally, a circuit is the path that allows electricity to flow. If you know what to look for, it’ll become second nature. While at first you’ll just be reading them, eventually you will start creating your own. This guide will show you a few of the common symbols that you are sure to see in your future electrical engineering career.
By Bertille Solange. Circuit. Published at Saturday, December 23rd 2017, 09:32:45 AM. Voltage is measured in units of Joules per Coulomb, known as a Volt (V). It is important to remember that voltage is not an absolute quantity, rather, it is always considered as a relative value between two points. In an electronic circuit, the electromagnetic problem of voltages at arbitrary points in space is typically simplified to voltages between nodes of circuit components such as resistors, capacitors, and transistors
By Cyrielle Marjolaine. Circuit. Published at Saturday, December 23rd 2017, 07:55:27 AM. Since single-layer/single-sided PCBs only have their various circuits and electrical components soldered onto one side, they are easy to design and manufacture. This popularity means that they can be purchased at a low-cost, especially for high-volume orders. The low-cost, high volume model means they are commonly used for a variety of applications, including calculators, cameras, radio and stereo equipment, solid state drives, printers and power supplies.
By Valentine Sybille. Circuit. Published at Saturday, December 23rd 2017, 06:21:14 AM. If the components are connected in a parallel format they would be termed to be a parallel series. In this sort of a connection all the components would receive the same voltage, while the current would be divided amongst the components.
By Charlotte Myriam. Circuit. Published at Saturday, December 23rd 2017, 05:24:16 AM. An often used and sometimes confusing term in electronic circuits is the word ground. The ground is a circuit node to which all voltages in a circuit are referenced. In a constant voltage supply circuit, one terminal from each voltage supply is typically connected to ground, or is grounded. For example, the negative terminal of a positive power supply is usually connected to ground so that any current drawn out of the positive terminal can be put back into the negative terminal via ground.
By Sasha Sara. Circuit. Published at Saturday, December 23rd 2017, 04:43:39 AM. A basic understanding of electronic circuits is important even if the designer does not intend to become a proficient electrical engineer. In many real-life engineering projects, it is often necessary to communicate, and also negotiate, specifications between engineering teams having different areas of expertise. Therefore, a basic understanding of electronic circuits will allow the mechanical engineer to evaluate whether or not a given electrical specification is reasonable and feasible.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.