By Valentine Sybille. Power. Publised at Sunday, November 26th 2017, 07:35:26 AM. Line regulation refers to the ability of the voltage regulator to reject variations in the applied voltage (often referred to as the line voltage because it is usually derived from the AC power line) and is expressed as a percentage. Ideally, the line regulation would be zero percent meaning that the output voltage is perfectly independent of the line voltage. The equation for line regulation is as follows. Note that line voltage can also mean the DC input voltage for some applications. Line regulation always refers to whatever the input of interest is. Line regulation is expressed in percent and the ideal value is zero meaning that the output voltage is completely independent of the input voltage.
By Madeleine Catherine. Power. Published at Monday, December 18th 2017, 05:46:00 AM. There are many new regulators which have tighter output tolerances (better than 2% is common), achieved through the use of a laser-trim process. Also, many of the new regulators have separate output specifications that cover room temperature/full operating temperature range, and full-load/light-load conditions.
By Jessica Mireille. Circuit. Published at Monday, December 18th 2017, 05:40:39 AM. Impedance is one of the most important concepts in electronic circuits. The purpose of impedance is to generalize the idea of resistance to create a component. To capture the behavior of resistors, capacitors, and inductors, for steadystate sinusoidal signals. This generalization is motivated by the fact that as long as the circuit is linear, its behavior can be analyzed using KVL and KCL.
By Lydie Honorine. Diagram. Published at Monday, December 18th 2017, 05:16:38 AM. Starting to make sense? These are the basics and may even seem obvious or intuitive to you, such as the wires and if they are connected. Whenever you determine your specific field of electrical engineering, you may see more complex diagrams and symbols. You’ll learn also that different countries use different symbols. For example, of the two symbols for resistors above, the first one is used in the U.S., while the second is used in Europe. You will also learn about the various symbols used for switches, other power supplies, inductors, meters, lamps, LEDs, transistors, antennas, and much more.
By Madeleine Catherine. Diagram. Published at Monday, December 18th 2017, 04:49:04 AM. Be sure to use this to produce a schematic if you need to ask questions about your circuit. It will help others to quickly understand the circuit diagrams are pictures with symbols that have differed from country to country and have changed over time, but are now to a large extent internationally standardized. Simple components often had symbols intended to represent some feature of the physical construction of the device. For example, the symbol for a resistor shown here dates back to the days when that component was made from a long piece of wire wrapped in such a manner as to not produce inductance, which would have made it a coil. These wirewound resistors are now used only in high-power applications, smaller resistors being cast from carbon composition (a mixture of carbon and filler) or fabricated as an insulating tube or chip coated with a metal film. The internationally standardized symbol for a resistor is therefore now simplified to an oblong, sometimes with the value in ohms written inside, instead of the zig-zag symbol. A less common symbol is simply a series of peaks on one side of the line representing the conductor, rather than back-and-forth as shown here. Components and connections involved in your design.
By Valentine Sybille. Circuit. Published at Monday, December 18th 2017, 04:45:11 AM. An inductor is a device that stores energy in the form of current. The most common form of inductors is a wire wound into a coil. The magnetic field generated by the wire creates a counter-acting electric field which impedes changes to the current.
By Cyrielle Marjolaine. Circuit. Published at Sunday, December 17th 2017, 15:08:00 PM. Double-layer or double-sided PCBs have a base material with a thin layer of conductive metal, like copper, applied to both sides of the board. Holes drilled through the board allow circuits on one side of the board to connect to circuits on the other.
By Bertille Solange. Power. Published at Sunday, December 17th 2017, 14:30:46 PM. If the load current increases to the limiting value, the current limiting circuitry will take control and force the load current to the set limiting value (overriding the voltage error amplifier). The voltage error amplifier can resume control only if the load current is reduced sufficiently to cause the current limiting circuits to release control. This is covered in detail in the "Current Limiting" section.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.