By Madeleine Catherine. Circuit. Publised at Saturday, August 05th 2017, 15:56:27 PM. When a voltage is applied across a conductor, a current will begin to flow. The ratio between voltage and current is known as resistance. For most metallic conductors, the relationship between voltage and current is linear.
By Cyrielle Marjolaine. Circuit. Published at Sunday, November 19th 2017, 23:05:33 PM. An electric current is defined as free flow of electrons and the motivating force behind that free flow of electrons is called Voltage. Voltage is the measurement of potential energy that would move the electrons between two points. Voltage is the push that the electrons require to move within a circuit. Voltage is measured by Volt and Current is measured by Ampere.
By Valentine Sybille. Circuit. Published at Sunday, November 19th 2017, 22:33:06 PM. In the hydrodynamic analogy of electronic circuits, resistors are equivalent to a pipe. As fluid flows through a pipe, frictional drag forces at the walls dissipate energy from the flow and thus reducing the pressure, or equivalently, the potential energy of the fluid in the pipe. A small resistor is equivalent to a large diameter pipe that will allow for a high flow rate, whereas a large resistor is equivalent to a small diameter pipe that greatly constricts the flow rate.
By Alix Loane. Circuit. Published at Sunday, November 19th 2017, 22:10:34 PM. An often used and sometimes confusing term in electronic circuits is the word ground. The ground is a circuit node to which all voltages in a circuit are referenced. In a constant voltage supply circuit, one terminal from each voltage supply is typically connected to ground, or is grounded. For example, the negative terminal of a positive power supply is usually connected to ground so that any current drawn out of the positive terminal can be put back into the negative terminal via ground.
By Madeleine Catherine. Diagram. Published at Sunday, November 19th 2017, 21:57:33 PM. A digital circuit is constructed of a power supply, devices, and conduction nets. Some nets provide circuit inputs from the “outside world”; in a schematic, these input nets are generally shown entering the left side of component and/or the overall circuit. Other nets present circuit outputs to the outside world; these nets are generally shown exiting the schematic on the right. In the sample schematic below, circuit components are shown as arbitrary shapes, nets are shown as lines, and inputs and outputs are denoted by connector symbols.
By Charlotte Myriam. Power. Published at Sunday, November 19th 2017, 20:59:18 PM. The purpose of a voltage regulator is to maintain a constant voltage across a load regardless of variations in the applied input voltage and variations in the load current. Two metrics, line regulation and load regulation, are used to quantify the performance of a voltage regulator.
By Sasha Sara. Motor. Published at Sunday, November 19th 2017, 20:52:00 PM. If more than one drive is being operated from the power supply this is not a problem since the other drive(s) will absorb this current for its needs, unless it is decelerating as well. For this case or for a single drive it may be necessary to place a voltage clamp across the power supply in the form of a Zener diode. The voltage of this diode must be greater than the maximum expected power supply voltage, yet low enough to protect the drive. A good choice would be either 82 volts or 91 volts as standard values.
By Lydie Honorine. Diagram. Published at Sunday, November 19th 2017, 20:50:47 PM. There are two commonly used capacitor symbols. One symbol represents a polarized (usually electrolytic or tantalum) capacitor, and the other is for non-polarized caps. In each case there are two terminals, running perpendicularly into plates. The symbol with one curved plate indicates that the capacitor is polarized. The curved plate represents the cathode of the capacitor, which should be at a lower voltage than the positive, anode pin. A plus sign might also be added to the positive pin of the polarized capacitor symbol.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.