# Amplifier Circuit Design

## Class B Amplifier Circuit DiagramClass B Amplifier Circuit Diagram

By Madeleine Catherine. Circuit. Publised at Saturday, August 05th 2017, 15:56:27 PM. Ohm’s law states that the current through a conductor between two points is directly proportional to the potential difference across those two points. It means that more the resistance lesser current would flow. I=V/R This would apply to any component of a circuit. For example conductors would increase the current flow and the inductors would decrease it.

## Flip Flop CounterFlip Flop Counter

By Sasha Sara. Circuit. Published at Saturday, December 16th 2017, 07:52:40 AM. Double-layer or double-sided PCBs have a base material with a thin layer of conductive metal, like copper, applied to both sides of the board. Holes drilled through the board allow circuits on one side of the board to connect to circuits on the other.

## Programmable Logic ControlsProgrammable Logic Controls

By Cyrielle Marjolaine. Circuit. Published at Saturday, December 16th 2017, 06:37:27 AM. A simple low-pass filter circuit, which allows low frequency signals to pass through the circuit while attenuating high-frequency signals, can be made using a resistor and capacitor in series.The transfer function of this filter can be determined by analyzing the circuit as a voltage divider,

### Relaxation OscillatorRelaxation Oscillator

By Lydie Honorine. Circuit. Published at Saturday, December 16th 2017, 06:16:53 AM. In the hydrodynamic analogy of electronic circuits, resistors are equivalent to a pipe. As fluid flows through a pipe, frictional drag forces at the walls dissipate energy from the flow and thus reducing the pressure, or equivalently, the potential energy of the fluid in the pipe. A small resistor is equivalent to a large diameter pipe that will allow for a high flow rate, whereas a large resistor is equivalent to a small diameter pipe that greatly constricts the flow rate.

#### Dc CircuitDc Circuit

By Sasha Sara. Circuit. Published at Saturday, December 16th 2017, 04:15:41 AM. When multiple components are connected in series, each component must carry the same current. When multiple components are connected in parallel, the total current is the sum of the currents flowing through each individual component. These statements are generalized as Kirchoff’s Current Law (KCL), which states that the sum of currents entering and exiting a node must be zero.

##### Truth Table Of EncoderTruth Table Of Encoder

By Sasha Sara. Circuit. Published at Saturday, December 16th 2017, 01:33:00 AM. Electric circuits use electric power to perform some function, like energize a heating or lighting element, turn a motor, or create an electromagnetic filed. Electronic circuits differ from electric circuits in that they use devices that can themselves be controlled by other electric signals. Restated, electronic circuits are built from devices that use electricity to control electricity. Most electronic circuits use signals that are within 5 to 10 volts of ground; most circuits built within the past several years use signals that are within 3 to 5 volts from ground. Some electronic circuits represent information encoded as continuous voltage levels that can wander between the high and low voltage supply rails – these are called analog circuits. As an example, a sound pressure level transducer (i.e. a microphone) might drive a signal between 0V and 3.3V in direct proportion to the detected sound pressure level. In this case, the voltage signal output from the microphone is said to be an analog ifthe sound pressure wave itself. Other circuits use only two distinct voltage levels to represent information. Most often, these two voltage levels use the same voltages supplied by the power rails. In these circuits, called digital circuits, all information must be represented as binary numbers, with a signal at 0V (or ground) representing one kind of information, and a signal at 3.3V (or whatever the upper voltage supply rail provides) representing the other kind of information. In this series of modules, we will confine our discussions to digital circuits.

###### Rotary Encoder CircuitRotary Encoder Circuit

By Madeleine Catherine. Circuit. Published at Friday, December 15th 2017, 22:55:29 PM. Voltage is measured in units of Joules per Coulomb, known as a Volt (V). It is important to remember that voltage is not an absolute quantity, rather, it is always considered as a relative value between two points. In an electronic circuit, the electromagnetic problem of voltages at arbitrary points in space is typically simplified to voltages between nodes of circuit components such as resistors, capacitors, and transistors

## Schematic Symbol For LedSchematic Symbol For Led

By Bertille Solange. Diode. Published at Friday, December 15th 2017, 19:21:36 PM. You need not be familiar with the “diode equation” to analyze simple diode circuits. Just understand that the voltage dropped across a current-conducting diode does change with the amount of current going through it, but that this change is fairly small over a wide range of currents. This is why many textbooks simply say the voltage drop across a conducting, semiconductor diode remains constant at 0.7 volts for silicon and 0.3 volts for germanium. However, some circuits intentionally make use of the P-N junction’s inherent exponential current/voltage relationship and thus can only be understood in the context of this equation. Also, since temperature is a factor in the diode equation, a forward-biased P-N junction may also be used as a temperature-sensing device, and thus can only be understood if one has a conceptual grasp on this mathematical relationship.

Altrushare - Wiring Diagram Gallery

Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.