By Charlotte Myriam. Circuit. Publised at Tuesday, July 04th 2017, 03:38:49 AM. A simple low-pass filter circuit, which allows low frequency signals to pass through the circuit while attenuating high-frequency signals, can be made using a resistor and capacitor in series.The transfer function of this filter can be determined by analyzing the circuit as a voltage divider,
By Bertille Solange. Diagram. Published at Saturday, December 23rd 2017, 20:59:22 PM. Circuits often require output devices to communicate their state to an user. Examples of electronic output devices include computer monitors, LCD alphanumeric panels (as on a calculator), small lamps or light-emitting diodes (LED), etc. Digilent boards include different output devices, but all of them include some number of individual LED, and seven-segment LED displays that can display the digits 0-9 in each digit position (each segment in the seven-segment display contains a single LED). LED are two-terminal semiconductor devices that conduct current in only one direction (from the anode to the cathode). The small LED chips are secured inside a plastic housing, and they emit light at a givenfrequency (RED, YELLOW, etc.) when a small electric current (typically 10mA to 25mA) flows through them.
By Madeleine Catherine. Diagram. Published at Saturday, December 23rd 2017, 20:46:14 PM. Electronic components are often assembled and interconnected on a flat surface known as a circuit board. The several types of existing circuit boards may be divided into two broad categories: those intended for prototype or experimental circuits; and those intended for production and/or commercial sale. Circuit boards used for experimental work are often referred to as breadboards or protoboards. Breadboards allow engineers to construct circuits quickly, so that they can be studied and modified until an optimal design is discovered. In a typical breadboard use, components and wires are added to a circuit in an ad hoc manner as the design proceeds, with new data and new understanding dictating the course of the design. Since breadboard circuits exist only in the laboratory, no special consideration need be given to creating reliable or simple-to-manufacture circuits – the designer can focus exclusively on the circuits behavior. In contrast, circuit boards intended for production or commercial sale must have highly reliable wires and interconnects, permanent bonds to all components, and topographies amenable to mass production and thorough testing. And further, they must be made of a material that is reliable, low-cost, and easy to manufacture. A fiberglass substratewith copper wires (etched from laminated copper sheets) has been the PCB material of choice for the past several decades. The Digilent board is a simple example of such a board. Note that most often, production circuit board designs are finalized only after extensive breadboard phases. Components are permanently affixed to production boards using the soldering process.
By Valentine Sybille. Diagram. Published at Saturday, December 23rd 2017, 20:05:53 PM. A capacitor is a two-terminal device that can store electric energy in the form of charged particles. You can think of a capacitor as a reservoir of charge that takes time to fill or empty. The voltage across a capacitor is proportional to the amount of charge it is storing – the more charge added to a capacitor of a given size, the larger the voltage across the capacitor. It is not possible to instantaneously move charge to or from a capacitor, so it is not possible to instantaneously change the voltage across a capacitor. It is this property that makes capacitors useful on Digilent boards and in many other applications.
By Sasha Sara. Circuit. Published at Saturday, December 23rd 2017, 19:42:57 PM. Surface mount PCBs do not utilize wires as connectors. Instead, many small leads are soldered directly to the board, meaning that the board itself is used as a wiring surface for the different components. This allows circuits to be completed using less space, freeing up space to allow the board to complete more functions, usually at higher speeds and a lighter weight than a through-hole board would allow.
By Sasha Sara. Diagram. Published at Saturday, December 23rd 2017, 19:23:03 PM. The unloaded PCB appears green because thin sheets of green plastic have been applied to both sides (otherwise the PCB would appear pale yellow). Called solder masks, these sheets cover all exposed metal other than the component pads and holes so that errant solder can not inadvertently short (or electrically connect) the printed wires. All metal surfaces other than the exposed pads and holes (i.e., the wires) are underneath the solder mask. Not infrequently, blue or even red solder masks are used.
By Lydie Honorine. Circuit. Published at Saturday, December 23rd 2017, 18:22:12 PM. Ohm’s law states that the current through a conductor between two points is directly proportional to the potential difference across those two points. It means that more the resistance lesser current would flow. I=V/R This would apply to any component of a circuit. For example conductors would increase the current flow and the inductors would decrease it.
By Alix Loane. Diagram. Published at Saturday, December 23rd 2017, 17:48:37 PM. In a PCB that uses through-hole technology, holes are drilled through the pads so that component leads can be inserted and then fastened (soldered) in place. In a PCB that uses surface-mount technology, component leads are soldered directly to the pads on the surface. Each set of pads (or holes) in the PCB is intended to receive a particular component. To identify which component must be loaded where, reference designators are printed on the circuit board immediately adjacent to the pads using a silk-screen process. A parts list links a designated set of pads to a physical component by describing the component and assigning it a particular reference designator. The reference designators guide assemblers and testers when they are working with the PCB. Many components must be placed into the PCB in a particular orientation. By convention, components that require a particular orientation have one lead designated as pin 1. On the PCB, a square pad or silkscreen indicator typically denotes pin 1.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.