By Charlotte Myriam. Circuit. Publised at Tuesday, July 04th 2017, 03:38:49 AM. If the components are connected in a parallel format they would be termed to be a parallel series. In this sort of a connection all the components would receive the same voltage, while the current would be divided amongst the components.
By Valentine Sybille. Car Wiring. Published at Wednesday, January 10th 2018, 00:32:40 AM. On its downstroke, a piston draws air into the cylinder. On the compression stroke, the fuel injection system (depending on how it’s timed) sprays fuel into the combustion area, and the resulting cylinder pressure (and residual heat from previous firings) combusts the fuel/air mix, etc.
By Cyrielle Marjolaine. Motor. Published at Wednesday, January 10th 2018, 00:18:44 AM. To avoid confusion obtain a pocket motor wiring guide and refer to it while performing the work. We mentioned a catch, earlier. With these and other motor wiring variations possible, it’s easy to make a mistake. That drawing we said to follow could be wrong. Before you connect any wires, check the drawing carefully. That’s another reason to have that pocket motor wiring guide.
By Cyrielle Marjolaine. Motor. Published at Tuesday, January 09th 2018, 22:58:18 PM. Typically, the motor will be a 6-lead or 9-lead motor. Motors with six leads are nearly always single-voltage motors. Such motors might be dual-winding motors, in which case you can wire them for a part winding start. You can connect them for a delta start or a wye start.
By Bertille Solange. Circuit. Published at Tuesday, January 09th 2018, 21:42:21 PM. Electric circuits use electric power to perform some function, like energize a heating or lighting element, turn a motor, or create an electromagnetic filed. Electronic circuits differ from electric circuits in that they use devices that can themselves be controlled by other electric signals. Restated, electronic circuits are built from devices that use electricity to control electricity. Most electronic circuits use signals that are within 5 to 10 volts of ground; most circuits built within the past several years use signals that are within 3 to 5 volts from ground. Some electronic circuits represent information encoded as continuous voltage levels that can wander between the high and low voltage supply rails – these are called analog circuits. As an example, a sound pressure level transducer (i.e. a microphone) might drive a signal between 0V and 3.3V in direct proportion to the detected sound pressure level. In this case, the voltage signal output from the microphone is said to be an analog ifthe sound pressure wave itself. Other circuits use only two distinct voltage levels to represent information. Most often, these two voltage levels use the same voltages supplied by the power rails. In these circuits, called digital circuits, all information must be represented as binary numbers, with a signal at 0V (or ground) representing one kind of information, and a signal at 3.3V (or whatever the upper voltage supply rail provides) representing the other kind of information. In this series of modules, we will confine our discussions to digital circuits.
By Jessica Mireille. Car Wiring. Published at Tuesday, January 09th 2018, 21:35:41 PM. Plan out your wiring. Choose the path the wires will follow. Choose the locations of all of your switches, gauges, ignition box, battery, and charging posts. If your past layout was deficient, now is the time to rethink the entire plan.
By Charlotte Myriam. Car Wiring. Published at Tuesday, January 09th 2018, 20:33:26 PM. Most are wired through the ignition switch, so that they work only when the ignition is switched on. This prevents you accidentally leaving something switched on which might cause the battery to go flat. The side and tail lights, however, which you may need to leave on when the car is parked, are always wired independently of the ignition switch.
By Valentine Sybille. Circuit. Published at Tuesday, January 09th 2018, 17:51:25 PM. A single-layer or single-sided PCB is one that is made out of a single layer of base material or substrate. One side of the base material is coated with a thin layer of metal. Copper is the most common coating due to how well it functions as an electrical conductor. Once the copper base plating is applied, a protective solder mask is usually applied, followed by the last silk-screen to mark out all of the elements on the board.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.