By Charlotte Myriam. Circuit. Publised at Tuesday, July 04th 2017, 03:38:49 AM. Voltage is measured in units of Joules per Coulomb, known as a Volt (V). It is important to remember that voltage is not an absolute quantity, rather, it is always considered as a relative value between two points. In an electronic circuit, the electromagnetic problem of voltages at arbitrary points in space is typically simplified to voltages between nodes of circuit components such as resistors, capacitors, and transistors
By Bertille Solange. Circuit. Published at Monday, January 15th 2018, 19:06:47 PM. Electric circuits use electric power to perform some function, like energize a heating or lighting element, turn a motor, or create an electromagnetic filed. Electronic circuits differ from electric circuits in that they use devices that can themselves be controlled by other electric signals. Restated, electronic circuits are built from devices that use electricity to control electricity. Most electronic circuits use signals that are within 5 to 10 volts of ground; most circuits built within the past several years use signals that are within 3 to 5 volts from ground. Some electronic circuits represent information encoded as continuous voltage levels that can wander between the high and low voltage supply rails – these are called analog circuits. As an example, a sound pressure level transducer (i.e. a microphone) might drive a signal between 0V and 3.3V in direct proportion to the detected sound pressure level. In this case, the voltage signal output from the microphone is said to be an analog ifthe sound pressure wave itself. Other circuits use only two distinct voltage levels to represent information. Most often, these two voltage levels use the same voltages supplied by the power rails. In these circuits, called digital circuits, all information must be represented as binary numbers, with a signal at 0V (or ground) representing one kind of information, and a signal at 3.3V (or whatever the upper voltage supply rail provides) representing the other kind of information. In this series of modules, we will confine our discussions to digital circuits.
By Bertille Solange. Motor. Published at Monday, January 15th 2018, 17:21:59 PM. If one changes the power supply voltage, then a new family of speed-torque curves result. As an example, if the power supply voltage is doubled then a new curve is generated; the curve now has twice the torque at any given speed in region 2. Since power equals torque times speed, the motor now generates twice as much power as well.
By Alix Loane. Motor. Published at Sunday, January 14th 2018, 19:23:49 PM. Eddy current and hysteresis heating are collectively called iron losses. The former induces currents in the iron of the motor while the latter is caused by the re-alignment of the magnetic domains in the iron. You can think of this as “friction heating” as the magnetic dipoles in the iron switch back and forth. Either way, both cause the bulk heating of the motor. Iron losses are a function of AC current and therefore the power supply voltage.
By Valentine Sybille. Motor. Published at Saturday, January 13th 2018, 16:12:10 PM. The result will be in microfarads for the capacitor if the value for “I” is amperes of current needed and “V” is the output voltage of the supply. When picking the capacitor, any value equal to or greater than the calculated value can be used. Be sure to use a capacitor with a voltage rating at least 20% higher than the output voltage of the power supply.
By Madeleine Catherine. Diagram. Published at Saturday, January 13th 2018, 10:10:30 AM. A block diagram shows a higher level (or organizational layout) of functional units in a circuit (or a device, machine, or collection of these). It is meant to show data flow or organization between separate units of function. A block diagram gives you an overview of the interconnected nature of circuit assemblies or components.
By Cyrielle Marjolaine. Car Wiring. Published at Saturday, January 13th 2018, 05:56:26 AM. The electrical system of a car is a closed circuit with an independent power source the battery. It operates on a small fraction of the power of a household circuit. Current flows along a single cable from the battery to the component being powered, and back to the battery through the cars metal body. The body is connected to the earth terminal of the battery by a thick cable.
By Alix Loane. Diagram. Published at Friday, January 12th 2018, 22:42:48 PM. There are drawing programs, and there are schematic capture programs. All schematic capture programs will produce output for inclusion in publications. However, these programs have different goals, and it shows. Rarely is the output of a schematic capture program really suitable for publication; often it is not even readable, or cannot be scaled. Engineers who really want to have a useful schematic drawing of a circuit usually redraw the circuit in a general drawing program, which can be both tedious and prone to introducing new errors.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.