By Charlotte Myriam. Circuit. Publised at Tuesday, July 04th 2017, 03:38:49 AM. In some circuits, there are virtual grounds, which are nodes at the same voltage as ground, but are not connected to a power supply. When current flows into the virtual ground, the voltage at the virtual ground may change relative to the real ground, and the consequences of this situation must be analyzed carefully.
By Sasha Sara. Circuit. Published at Wednesday, January 10th 2018, 13:48:10 PM. For DC signals, the linearity of the system implies that H is independent of Vin. For dynamic signals, the transfer function cannot in general be described simply. However, if the input is a sinusoidal signal then the output must also be a sinusoidal signal with the same frequency but possibly a different amplitude and phase. In other words, a linear system can only modify the amplitude and phase of a sinusoidal input.
By Valentine Sybille. Motor. Published at Wednesday, January 10th 2018, 06:56:10 AM. The voltage of your power supply is entirely dependent on the inductance rating of your motor, which we learned is translatable to the number of turns of wire in the stator. Every motor model will have a different inductance rating and will therefore have a different maximum voltage. To figure out what the maximum power supply voltage should be, use the following formula with the motor’s inductance in millihenries (mH) used for the L value.
By Charlotte Myriam. Car Wiring. Published at Wednesday, January 10th 2018, 04:08:19 AM. The electrical system of a car is a closed circuit with an independent power source the battery. It operates on a small fraction of the power of a household circuit. Current flows along a single cable from the battery to the component being powered, and back to the battery through the cars metal body. The body is connected to the earth terminal of the battery by a thick cable.
By Cyrielle Marjolaine. Diagram. Published at Wednesday, January 10th 2018, 00:54:54 AM. In contrast to digital circuits, analog circuits use signals whose voltage levels are not constrained to two distinct levels, but instead can assume any value between Vdd and GND. Many input devices, particularly those using electronic sensors (e.g., microphones, cameras, thermometers, pressure sensors, motion and proximity detectors, etc.) produce analog voltages at their outputs. In modern electronic devices, it is likely that such signals will be converted to digital signals before they are used within the device. For example, a digital voice-memo recording device uses an analog microphone circuit to convert sound pressure waves into voltage waves on an internal circuit node. A special circuit called an analog-to-digital converter, or ADC, converts that analog voltage to a binary number that can be represented as a bus in a digital circuit. An ADC functions by taking samples of the input analog signal, measuring the magnitude of the input voltage signal (usually with reference to GND), and assigning a binary number to the measured magnitude. Once an analog signal has been converted to a binary number, a bus can carry that digital information around a circuit. In a similar manner, digital signals can be reconstituted into analog signals using a digital-to-analog converter. Thus, a binary number that represents a sample of an audio waveform can be converted to an analog signal that can, for example, drive a speaker.
By Valentine Sybille. Car Wiring. Published at Wednesday, January 10th 2018, 00:32:40 AM. As for the gauges, new designs are coming out all the time. If you have a hard time seeing your gauges at night, then the new brightly lit types might be the thing to now install. According to Dick, it is important to use a high-quality tachometer. Accuracy of rpm is very important to choosing the right gear.
By Cyrielle Marjolaine. Motor. Published at Wednesday, January 10th 2018, 00:18:44 AM. Electrically, a real motor differs from an ideal one primarily by having a non-zero winding resistance. Also, the iron in the motor is subject to magnetic saturation, as well as having eddy current and hysteresis losses. Magnetic saturation sets a limit on current to torque proportionally while eddy current and hysteresis (iron losses) along with winding resistance (copper losses) cause motor heating.
By Cyrielle Marjolaine. Motor. Published at Tuesday, January 09th 2018, 22:58:18 PM. An unregulated power supply will be sufficient and is recommended for most applications because of its simplicity. If a motor with a large inertial load decelerates quickly it will act as an alternator and send voltage back to the drive which then sends it back to the power supply. Because many regulated power supplies feature protection circuitry this may cause the power supply to fault or reset; however, if the supply is unregulated it will simply get absorbed by the filter capacitor.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.