By Charlotte Myriam. Circuit. Publised at Tuesday, July 04th 2017, 03:38:49 AM. The circuits and components of a double-layer PCB board are usually connected in one of two ways: either utilizing a through-hole or with the use of a surface-mount. A through-hole connection means that small wires, known as leads, are fed through the holes, with each end of the leads then soldered to the right component.
By Cyrielle Marjolaine. Diagram. Published at Monday, December 18th 2017, 13:32:30 PM. A schematic shows connections in a circuit in a way that is clear and standardized. It is a way of communicating to other engineers exactly what components are involved in a circuit as well as how they are connected. A good schematic will show component names and values, and provide labels for sections or components to help communicate the intended purpose. Note how connections on wires (or "nets") are shown using dots and non-connections are shown without a dot.
By Bertille Solange. Power. Published at Monday, December 18th 2017, 13:09:45 PM. A variation of the Standard regulator is the quasi-LDO, which uses an NPN and PNP transistor as the pass device. The dropout voltage for a quasi-LDO delivering rated current is usually specified at about 1.5V(max). The actual dropout voltage is temperature and load current dependent, but could never be expected to go lower than about 0.9V (25°C) at even the lightest load. The dropout voltage for the quasi-LDO is higher than the LDO, but lower than the Standard regulator.
By Charlotte Myriam. Diagram. Published at Monday, December 18th 2017, 12:40:04 PM. Learning about basic electronics and creating your own projects is a lot easier than you may think. In this tutorial, we’re going to give you a brief overview of common electronic components and explain what their functions are. You will then learn about schematic diagrams and how they are used to design and build circuits. And finally, you will put this information to use by creating your first basic circuit.
By Jessica Mireille. Amplifier. Published at Monday, December 18th 2017, 11:38:21 AM. An input signal will cause the transistor to operate as normal in its Active region thereby eliminating any crossover distortion which is present in class B configurations. A small Collector current will flow when there is no input signal but it is much less than that for the Class A amplifier configuration.
By Lydie Honorine. Diagram. Published at Monday, December 18th 2017, 11:22:07 AM. A digital circuit requires a power supply to provide a constant and stable source of electric power to all devices. As discussed above, electric power is derived from the basic electrical forces that charged particles (e.g., protons and electrons) exert on one another – namely, electrons are repelled by other electrons, and attracted to more electrically positive areas where there are relatively fewer electrons. The vast majority of charged particles are found in ordinary matter bound in electrically neutral atomic structures (that is, most particles are found in structures that have an equal number of positive and negative particles). Some electrically neutral conducting materials (like metals) contain electrons that are not so tightly bound to their host atoms. If a voltage source is applied to these materials, the lightly bound electrons will move away from the concentrated source of electrons on the negative side of the supply towards the electrically positive side of the supply. A “power supply” in a digital circuit provides a local, contained imbalance of electrons that provides a voltage source that can do useful work, such as transmitting information through a conductor from one device to another. A digital circuit allows a controlled flow of electrons from of the negative to positive side of the power supply, but only via the paths designed into the circuit. As electrons flow to and from the devices in a given circuit, they can change device properties in useful ways.
By Cyrielle Marjolaine. Power. Published at Monday, December 18th 2017, 10:47:11 AM. The output resistance (also known as source resistance) of a voltage regulator is a close cousin of its load regulation. Figure 1 illustrates how the output voltage of a regulator typically changes as a function of load current. Initially, the slope is quite linear but once the load current becomes higher than the design then the voltage will often drop rapidly with an increase in current. We measure the output resistance only on the linear portion of the plot in the normal operating region. It is meaningless to use a point in the overload area as that will result in an artificially high output resistance.
By Bertille Solange. Diagram. Published at Monday, December 18th 2017, 09:48:57 AM. A schematic shows connections in a circuit in a way that is clear and standardized. It is a way of communicating to other engineers exactly what components are involved in a circuit as well as how they are connected. A good schematic will show component names and values, and provide labels for sections or components to help communicate the intended purpose. Note how connections on wires (or "nets") are shown using dots and non-connections are shown without a dot.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.