By Charlotte Myriam. Circuit. Publised at Tuesday, July 04th 2017, 03:38:49 AM. The real part and imaginary part of impedance are interpreted as a resistive part that dissipates energy and a reactive part that stores energy. Resistors can only dissipate energy and therefore their impedances have only a real part. Capacitors and inductors can only store energy and therefore their impedances have only an imaginary part. When resistors, capacitors, and inductors are combined, the overall impedance may have both real and imaginary parts. It is important to note that the definition of impedance preserves the definition of resistance.
By Sasha Sara. Diagram. Published at Tuesday, July 25th 2017, 11:46:43 AM. Electronic components are often assembled and interconnected on a flat surface known as a circuit board. The several types of existing circuit boards may be divided into two broad categories: those intended for prototype or experimental circuits; and those intended for production and/or commercial sale. Circuit boards used for experimental work are often referred to as breadboards or protoboards. Breadboards allow engineers to construct circuits quickly, so that they can be studied and modified until an optimal design is discovered. In a typical breadboard use, components and wires are added to a circuit in an ad hoc manner as the design proceeds, with new data and new understanding dictating the course of the design. Since breadboard circuits exist only in the laboratory, no special consideration need be given to creating reliable or simple-to-manufacture circuits – the designer can focus exclusively on the circuits behavior. In contrast, circuit boards intended for production or commercial sale must have highly reliable wires and interconnects, permanent bonds to all components, and topographies amenable to mass production and thorough testing. And further, they must be made of a material that is reliable, low-cost, and easy to manufacture. A fiberglass substratewith copper wires (etched from laminated copper sheets) has been the PCB material of choice for the past several decades. The Digilent board is a simple example of such a board. Note that most often, production circuit board designs are finalized only after extensive breadboard phases. Components are permanently affixed to production boards using the soldering process.
By Cyrielle Marjolaine. Diode. Published at Saturday, July 22nd 2017, 10:45:28 AM. Diodes are made from semiconductor materials, mainly silicon, with various compounds (combinations of more than one element) and metals added depending on the function of the diode. Early types of semiconductor diodes were made from Selenium and Germanium, but these diode types have been almost totally replaced by more modern silicon designs.
By Sasha Sara. Diagram. Published at Thursday, July 20th 2017, 10:43:41 AM. A schematic shows connections in a circuit in a way that is clear and standardized. It is a way of communicating to other engineers exactly what components are involved in a circuit as well as how they are connected. A good schematic will show component names and values, and provide labels for sections or components to help communicate the intended purpose. Note how connections on wires (or "nets") are shown using dots and non-connections are shown without a dot.
By Cyrielle Marjolaine. Power. Published at Tuesday, July 18th 2017, 09:13:33 AM. The quiescent current that a part draws from the source when idling (either shut down or not delivering significant amounts of load current) can be of critical importance in battery-powered applications.
By Cyrielle Marjolaine. Diagram. Published at Thursday, July 13th 2017, 08:59:25 AM. A digital circuit requires a power supply to provide a constant and stable source of electric power to all devices. As discussed above, electric power is derived from the basic electrical forces that charged particles (e.g., protons and electrons) exert on one another – namely, electrons are repelled by other electrons, and attracted to more electrically positive areas where there are relatively fewer electrons. The vast majority of charged particles are found in ordinary matter bound in electrically neutral atomic structures (that is, most particles are found in structures that have an equal number of positive and negative particles). Some electrically neutral conducting materials (like metals) contain electrons that are not so tightly bound to their host atoms. If a voltage source is applied to these materials, the lightly bound electrons will move away from the concentrated source of electrons on the negative side of the supply towards the electrically positive side of the supply. A “power supply” in a digital circuit provides a local, contained imbalance of electrons that provides a voltage source that can do useful work, such as transmitting information through a conductor from one device to another. A digital circuit allows a controlled flow of electrons from of the negative to positive side of the power supply, but only via the paths designed into the circuit. As electrons flow to and from the devices in a given circuit, they can change device properties in useful ways.
By Valentine Sybille. Circuit. Published at Monday, July 10th 2017, 06:11:26 AM. First let’s understand the difference between these two terms. While electrical is the basis of everything, electronic is a subset of electrical. An electrical circuit deals with just the flow of electrons and has components like resistors, inductors and capacitors and uses Alternating Current Source; while electronic circuit deals with the transformation of current and controlling the motion of the electrons and uses Direct Current Source. An electrical circuit is termed as Passive because it doesn’t have any such component that reacts to the current/voltage that passes through them and electronic circuit is called active because of the additional components like diode or a transformer that react to the current/voltage that passes through.
By Sasha Sara. Power. Published at Friday, July 07th 2017, 05:33:01 AM. The control circuitry must monitor (sense) the output voltage, and adjust the current source (as required by the load) to hold the output voltage at the desired value. The design limit of the current source defines the maximum load current the regulator can source and still maintain regulation.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.