By Charlotte Myriam. Circuit. Publised at Tuesday, July 04th 2017, 03:38:49 AM. The circuits and components of a double-layer PCB board are usually connected in one of two ways: either utilizing a through-hole or with the use of a surface-mount. A through-hole connection means that small wires, known as leads, are fed through the holes, with each end of the leads then soldered to the right component.
By Sasha Sara. Diagram. Published at Friday, October 20th 2017, 16:52:54 PM. As discussed earlier, a digital circuit represents and manipulates information encoded as electric signals that can assume one of two voltages – logic-high voltage (or Vdd) and logic-low voltage (or GND). A digital circuit requires a power supply that can produce these two voltages, and these same supply voltages are also used to encode information in the form of two-state, or binary signals. Thus,if a given circuit node is at Vdd, then that signal is said to carry a logic ‘1’; if the node is at GND, then the node carries a logic ‘0’. The components in digital circuits are simple on/off switches that can pass logic ‘1’ and logic ‘0’ signals from one circuit node to another. Most typically, these switches are arranged to combine input signals to produce an output signal according to basic logic relationships. For example, one well-known logic circuit is an AND gate that combines two input signals to produce an output that is the logic AND of the inputs (i.e., if both input1 and input2 are a ‘1’, then the output is a ‘1’).
By Charlotte Myriam. Diagram. Published at Wednesday, October 18th 2017, 16:30:19 PM. A block diagram shows a higher level (or organizational layout) of functional units in a circuit (or a device, machine, or collection of these). It is meant to show data flow or organization between separate units of function. A block diagram gives you an overview of the interconnected nature of circuit assemblies or components.
By Valentine Sybille. Power. Published at Monday, October 16th 2017, 15:16:58 PM. Linear IC regulators contain built-in protection circuits which make them virtually immune to damage from either excessive load current or high operating temperature.
By Lydie Honorine. Circuit. Published at Friday, October 13th 2017, 13:12:13 PM. A capacitor is a device that stores energy in the form of voltage. The most common form of capacitors is made of two parallel plates separated by a dielectric material. Charges of opposite polarity can be deposited on the plates, resulting in a voltage V across the capacitor plates. Capacitance is a measure of the amount of electrical charge required to build up one unit of voltage across the plates.
By Madeleine Catherine. Diagram. Published at Thursday, October 12th 2017, 12:26:33 PM. Starting to make sense? These are the basics and may even seem obvious or intuitive to you, such as the wires and if they are connected. Whenever you determine your specific field of electrical engineering, you may see more complex diagrams and symbols. You’ll learn also that different countries use different symbols. For example, of the two symbols for resistors above, the first one is used in the U.S., while the second is used in Europe. You will also learn about the various symbols used for switches, other power supplies, inductors, meters, lamps, LEDs, transistors, antennas, and much more.
By Valentine Sybille. Circuit. Published at Tuesday, October 10th 2017, 11:14:52 AM. A collection of electronic components that have been assembled and interconnected to perform a given function is commonly referred to as a circuit. The word circuit derives from the fact that electric power must flow from the positive terminal of a power source through one or more electronic devices and back to the negative terminal of a power source, thereby forming a circuit. If the connections between an electronic device and either the positive or negative terminals of a power supply are interrupted, the circuit will be broken and the device will not function.
By Charlotte Myriam. Circuit. Published at Monday, October 09th 2017, 11:02:09 AM. Electric circuits use electric power to perform some function, like energize a heating or lighting element, turn a motor, or create an electromagnetic filed. Electronic circuits differ from electric circuits in that they use devices that can themselves be controlled by other electric signals. Restated, electronic circuits are built from devices that use electricity to control electricity. Most electronic circuits use signals that are within 5 to 10 volts of ground; most circuits built within the past several years use signals that are within 3 to 5 volts from ground. Some electronic circuits represent information encoded as continuous voltage levels that can wander between the high and low voltage supply rails – these are called analog circuits. As an example, a sound pressure level transducer (i.e. a microphone) might drive a signal between 0V and 3.3V in direct proportion to the detected sound pressure level. In this case, the voltage signal output from the microphone is said to be an analog ifthe sound pressure wave itself. Other circuits use only two distinct voltage levels to represent information. Most often, these two voltage levels use the same voltages supplied by the power rails. In these circuits, called digital circuits, all information must be represented as binary numbers, with a signal at 0V (or ground) representing one kind of information, and a signal at 3.3V (or whatever the upper voltage supply rail provides) representing the other kind of information. In this series of modules, we will confine our discussions to digital circuits.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.