By Charlotte Myriam. Circuit. Publised at Tuesday, July 04th 2017, 03:38:49 AM. An intuitive way to understand the behavior of voltage and current in electronic circuits is to use hydrodynamic systems as an analogue. In this system, voltage is represented by gravitational potential or height of the fluid column, and current is represented by the fluid flow rate.
By Charlotte Myriam. Car Wiring. Published at Tuesday, January 09th 2018, 20:33:26 PM. Wire and cable sizes are classified by the maximum amperage that they can carry safely. A complex network of wires runs through the car. To avoid confusion, each wire is colour coded (but only within the car: there is no national or international system of colour-coding).
By Valentine Sybille. Circuit. Published at Tuesday, January 09th 2018, 17:51:25 PM. If the components of the circuit are connected in one single path is it termed as series. The same current would flow through all the components while the voltage would differ from one component to another. For example you have lit three lamps in series to the same power source, the first one would receive more voltage than the last.
By Jessica Mireille. Car Wiring. Published at Tuesday, January 09th 2018, 14:36:01 PM. In the unfortunate case of a fire, and it does happen, you can remove all of the old wiring and what they were attached to, and reinstall all new switches, gauges, ignition box, and so on, and the wiring will be ready to install quickly and easily.
By Charlotte Myriam. Diagram. Published at Tuesday, January 09th 2018, 00:41:41 AM. Voltage nodes are single-terminal schematic components, which we can connect component terminals to in order to assign them to a specific voltage level. These are a special application of net names, meaning all terminals connected to a like-named voltage node are connected together.
By Lydie Honorine. Diagram. Published at Monday, January 08th 2018, 17:19:46 PM. In contrast to digital circuits, analog circuits use signals whose voltage levels are not constrained to two distinct levels, but instead can assume any value between Vdd and GND. Many input devices, particularly those using electronic sensors (e.g., microphones, cameras, thermometers, pressure sensors, motion and proximity detectors, etc.) produce analog voltages at their outputs. In modern electronic devices, it is likely that such signals will be converted to digital signals before they are used within the device. For example, a digital voice-memo recording device uses an analog microphone circuit to convert sound pressure waves into voltage waves on an internal circuit node. A special circuit called an analog-to-digital converter, or ADC, converts that analog voltage to a binary number that can be represented as a bus in a digital circuit. An ADC functions by taking samples of the input analog signal, measuring the magnitude of the input voltage signal (usually with reference to GND), and assigning a binary number to the measured magnitude. Once an analog signal has been converted to a binary number, a bus can carry that digital information around a circuit. In a similar manner, digital signals can be reconstituted into analog signals using a digital-to-analog converter. Thus, a binary number that represents a sample of an audio waveform can be converted to an analog signal that can, for example, drive a speaker.
By Valentine Sybille. Diagram. Published at Monday, January 08th 2018, 15:30:16 PM. Wiring diagrams use standard symbols for wiring devices, usually different from those used on schematic diagrams. The electrical symbols not only show where something is to be installed, but also what type of device is being installed. For example, a surface ceiling light is shown by one symbol, a recessed ceiling light has a different symbol, and a surface fluorescent light has another symbol. Each type of switch has a different symbol and so do the various outlets. There are symbols that show the location of smoke detectors, the doorbell chime, and thermostat. On large projects symbols may be numbered to show, for example, the panel board and circuit to which the device connects, and also to identify which of several types of fixture are to be installed at that location.
By Cyrielle Marjolaine. Diagram. Published at Monday, January 08th 2018, 11:14:03 AM. Knowing how to read circuits is a very useful skill that will help you out all the time. especially if you start messing around with building little electronics projects.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.