By Cyrielle Marjolaine. Motor. Publised at Thursday, June 29th 2017, 01:05:11 AM. The drive remedies this instability by adding a second-order, or viscous, damping. This damping decreases the total phase lag so the motor cannot sustain oscillation, much in the same way shock absorbers damp the mass-spring suspension of a vehicle.
By Alix Loane. Circuit. Publised at Tuesday, December 26th 2017, 19:02:52 PM. First let’s understand the difference between these two terms. While electrical is the basis of everything, electronic is a subset of electrical. An electrical circuit deals with just the flow of electrons and has components like resistors, inductors and capacitors and uses Alternating Current Source; while electronic circuit deals with the transformation of current and controlling the motion of the electrons and uses Direct Current Source. An electrical circuit is termed as Passive because it doesn’t have any such component that reacts to the current/voltage that passes through them and electronic circuit is called active because of the additional components like diode or a transformer that react to the current/voltage that passes through.
By Charlotte Myriam. Diagram. Published at Wednesday, December 20th 2017, 01:43:59 AM. A digital circuit requires a power supply to provide a constant and stable source of electric power to all devices. As discussed above, electric power is derived from the basic electrical forces that charged particles (e.g., protons and electrons) exert on one another – namely, electrons are repelled by other electrons, and attracted to more electrically positive areas where there are relatively fewer electrons. The vast majority of charged particles are found in ordinary matter bound in electrically neutral atomic structures (that is, most particles are found in structures that have an equal number of positive and negative particles). Some electrically neutral conducting materials (like metals) contain electrons that are not so tightly bound to their host atoms. If a voltage source is applied to these materials, the lightly bound electrons will move away from the concentrated source of electrons on the negative side of the supply towards the electrically positive side of the supply. A “power supply” in a digital circuit provides a local, contained imbalance of electrons that provides a voltage source that can do useful work, such as transmitting information through a conductor from one device to another. A digital circuit allows a controlled flow of electrons from of the negative to positive side of the power supply, but only via the paths designed into the circuit. As electrons flow to and from the devices in a given circuit, they can change device properties in useful ways.
By Madeleine Catherine. Diagram. Published at Tuesday, December 19th 2017, 18:21:54 PM. Most of the electrical symbols can be changed in their appearance, styles and colors according to users requirements. Electrical symbols are used to represent various electrical and electronic devices in a schematic diagram of an electrical or electronic circuit.
By Alix Loane. Circuit. Published at Tuesday, December 19th 2017, 18:18:50 PM. Impedance essentially can be viewed as frequency-dependent resistance. While resistance of a circuit is the instantaneous ratio between voltage and current, impedance of a circuit is the ratio between voltage and current for steady-state sinusoidal signals, which can vary with of frequency. As the later parts of this section will show, the voltage and current caused by applying a steady-state sinusoidal signal to any combination of resistors, capacitors, and inductors, are related by a constant factor and a phase shift. Therefore, impedance can be expressed by a complex constant using an extended version Ohm’s law.
By Sasha Sara. Diagram. Published at Tuesday, December 19th 2017, 17:18:01 PM. An electronic circuit is a circular path of conductors by which electric current can flow. A closed circuit is like a circle because it starts and ends at the same point forming a complete loop. Furthermore, a closed circuit allows electricity to flow from the (+) power to the (-) ground uninterrupted.
By Valentine Sybille. Circuit. Published at Tuesday, December 19th 2017, 16:50:18 PM. These are commonly termed as IC’s. They are usually in form of chips and microchips. This is a set of multiple electronic circuits on a small semiconductor device (normally silicon). With the advancement of technology, these IC’s prove to be extremely beneficial. They are present in any electronic device you can name. From computers, mobiles to other digital appliances you have multiple IC’s present in them. Their main components are a combination of Diodes, transistors and microprocessors. The microprocessors provide memory to the device. With the help of the microprocessor the electronic devices can perform logical or protocol applications.
By Madeleine Catherine. Diagram. Published at Tuesday, December 19th 2017, 16:05:42 PM. When working with circuits, you will often find something called a schematic diagram. These diagrams use symbols to illustrate what electronic components are used and where they’re placed in the circuit. These symbols are graphic representations of the actual electronic components.
By Charlotte Myriam. Circuit. Published at Tuesday, December 19th 2017, 15:29:49 PM. The circuits and components of a double-layer PCB board are usually connected in one of two ways: either utilizing a through-hole or with the use of a surface-mount. A through-hole connection means that small wires, known as leads, are fed through the holes, with each end of the leads then soldered to the right component.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.