By Cyrielle Marjolaine. Motor. Publised at Thursday, June 29th 2017, 01:05:11 AM. If you are using several different models of motors on the same power supply use the lowest inductance rating in the above formula. This will ensure that your motors will not overheat due to the voltage being too high.
By Valentine Sybille. Diagram. Published at Tuesday, December 26th 2017, 20:06:46 PM. Circuits often require output devices to communicate their state to an user. Examples of electronic output devices include computer monitors, LCD alphanumeric panels (as on a calculator), small lamps or light-emitting diodes (LED), etc. Digilent boards include different output devices, but all of them include some number of individual LED, and seven-segment LED displays that can display the digits 0-9 in each digit position (each segment in the seven-segment display contains a single LED). LED are two-terminal semiconductor devices that conduct current in only one direction (from the anode to the cathode). The small LED chips are secured inside a plastic housing, and they emit light at a givenfrequency (RED, YELLOW, etc.) when a small electric current (typically 10mA to 25mA) flows through them.
By Alix Loane. Circuit. Published at Tuesday, December 26th 2017, 19:02:52 PM. An electric current is defined as free flow of electrons and the motivating force behind that free flow of electrons is called Voltage. Voltage is the measurement of potential energy that would move the electrons between two points. Voltage is the push that the electrons require to move within a circuit. Voltage is measured by Volt and Current is measured by Ampere.
By Charlotte Myriam. Diagram. Published at Tuesday, December 26th 2017, 18:35:19 PM. In a digital circuit, power supply voltage levels are constrained to two distinct values – “logic high voltage” (called LHV or Vdd) and “logic low voltage” (called LLV or GND). The GND node in any circuit is the universal reference voltage against which all other voltages are measured (in modern digital circuits, GND is typically the lowest voltage in the circuit). In a schematic, it is often difficult to show lines connecting all GND nodes; rather, any nodes labeled GND are assumed to be connected into the same node. Often, a downward pointing triangle symbol, is attached to a GND node in addition to (or instead of) the GND label. The Vdd node in a digital circuit is typically the highest voltage, and all nodes labeled Vdd are tied together into the same node. Vdd may be thought of as the “source” of positive charges in a circuit, and GND may be thought of as the “source” of negative charges in a circuit. In modern digital systems, Vdd and GND are separated by anywhere from 1 to 5 volts. Older or inexpensive circuits typically use 5 volts, while newer circuits use 1-3 volts.
By Charlotte Myriam. Diode. Published at Tuesday, December 26th 2017, 14:27:42 PM. The above general rule notwithstanding, if the cathode voltage is positive relative to the anode voltage by a great enough amount, the diode will conduct current. The voltage required to produce this phenomenon, known as the avalanche voltage, varies greatly depending on the nature of the semiconductor material from which the device is fabricated. The avalanche voltage can range from a few volts up to several hundred volts.
By Jessica Mireille. Diagram. Published at Tuesday, December 26th 2017, 14:23:35 PM. In contrast to digital circuits, analog circuits use signals whose voltage levels are not constrained to two distinct levels, but instead can assume any value between Vdd and GND. Many input devices, particularly those using electronic sensors (e.g., microphones, cameras, thermometers, pressure sensors, motion and proximity detectors, etc.) produce analog voltages at their outputs. In modern electronic devices, it is likely that such signals will be converted to digital signals before they are used within the device. For example, a digital voice-memo recording device uses an analog microphone circuit to convert sound pressure waves into voltage waves on an internal circuit node. A special circuit called an analog-to-digital converter, or ADC, converts that analog voltage to a binary number that can be represented as a bus in a digital circuit. An ADC functions by taking samples of the input analog signal, measuring the magnitude of the input voltage signal (usually with reference to GND), and assigning a binary number to the measured magnitude. Once an analog signal has been converted to a binary number, a bus can carry that digital information around a circuit. In a similar manner, digital signals can be reconstituted into analog signals using a digital-to-analog converter. Thus, a binary number that represents a sample of an audio waveform can be converted to an analog signal that can, for example, drive a speaker.
By Alix Loane. Diagram. Published at Tuesday, December 26th 2017, 13:58:36 PM. Be sure to use this to produce a schematic if you need to ask questions about your circuit. It will help others to quickly understand the circuit diagrams are pictures with symbols that have differed from country to country and have changed over time, but are now to a large extent internationally standardized. Simple components often had symbols intended to represent some feature of the physical construction of the device. For example, the symbol for a resistor shown here dates back to the days when that component was made from a long piece of wire wrapped in such a manner as to not produce inductance, which would have made it a coil. These wirewound resistors are now used only in high-power applications, smaller resistors being cast from carbon composition (a mixture of carbon and filler) or fabricated as an insulating tube or chip coated with a metal film. The internationally standardized symbol for a resistor is therefore now simplified to an oblong, sometimes with the value in ohms written inside, instead of the zig-zag symbol. A less common symbol is simply a series of peaks on one side of the line representing the conductor, rather than back-and-forth as shown here. Components and connections involved in your design.
By Alix Loane. Circuit. Published at Tuesday, December 26th 2017, 13:48:36 PM. Since single-layer/single-sided PCBs only have their various circuits and electrical components soldered onto one side, they are easy to design and manufacture. This popularity means that they can be purchased at a low-cost, especially for high-volume orders. The low-cost, high volume model means they are commonly used for a variety of applications, including calculators, cameras, radio and stereo equipment, solid state drives, printers and power supplies.
Altrushare - Wiring Diagram Gallery
Copyright © 2003 - 2018 Domain Media. All sponsored products, company names, brand names, trademarks and logos arethe property of their respective owners.